X-Git-Url: https://review.openocd.org/gitweb?p=openocd.git;a=blobdiff_plain;f=doc%2Fopenocd.texi;h=58e533f629d3fc14c6b217486263994cedef939d;hp=4ce6e0426265c4470c5dcff9cd8641af154039b8;hb=ad18c1a47fb8f3eaae66a7314700a1f186391359;hpb=248161cbf47af9f7fc8c00b5efa79a1ff8e65848

diff --git a/doc/openocd.texi b/doc/openocd.texi
index 4ce6e04262..58e533f629 100644
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -2371,9 +2371,9 @@ This command is only available if your libusb1 is at least version 1.0.16.
 Specifies the @var{serial_string} of the adapter to use.
 If this command is not specified, serial strings are not checked.
 Only the following adapter drivers use the serial string from this command:
-cmsis_dap.
+cmsis_dap, ft232r, ftdi, jlink, kitprog, presto, vsllink, xds110.
 The following adapters have their own command to specify the serial string:
-ft232r, ftdi, hla, jlink, kitprog, presto, st-link, vsllink, xds110.
+hla, st-link.
 @end deffn
 
 @section Interface Drivers
@@ -2512,15 +2512,6 @@ of the adapter. If not specified, the device description is ignored
 during device selection.
 @end deffn
 
-@deffn {Config Command} {ftdi serial} serial-number
-Specifies the @var{serial-number} of the adapter to use,
-in case the vendor provides unique IDs and more than one adapter
-is connected to the host.
-If not specified, serial numbers are not considered.
-(Note that USB serial numbers can be arbitrary Unicode strings,
-and are not restricted to containing only decimal digits.)
-@end deffn
-
 @deffn {Config Command} {ftdi channel} channel
 Selects the channel of the FTDI device to use for MPSSE operations. Most
 adapters use the default, channel 0, but there are exceptions.
@@ -2641,12 +2632,6 @@ The vendor ID and product ID of the adapter. If not specified, default
 0x0403:0x6001 is used.
 @end deffn
 
-@deffn {Config Command} {ft232r serial_desc} @var{serial}
-Specifies the @var{serial} of the adapter to use, in case the
-vendor provides unique IDs and more than one adapter is connected to
-the host. If not specified, serial numbers are not considered.
-@end deffn
-
 @deffn {Config Command} {ft232r jtag_nums} @var{tck} @var{tms} @var{tdi} @var{tdo}
 Set four JTAG GPIO numbers at once.
 If not specified, default 0 3 1 2 or TXD CTS RXD RTS is used.
@@ -2863,12 +2848,6 @@ to the host. If not specified, USB addresses are not considered. Device
 selection via USB address is not always unambiguous. It is recommended to use
 the serial number instead, if possible.
 
-As a configuration command, it can be used only before 'init'.
-@end deffn
-@deffn {Config Command} {jlink serial} <serial number>
-Set the serial number of the interface, in case more than one adapter is
-connected to the host. If not specified, serial numbers are not considered.
-
 As a configuration command, it can be used only before 'init'.
 @end deffn
 @end deffn
@@ -2911,11 +2890,6 @@ Indicate that a PSoC acquisition sequence needs to be run during adapter init.
 Please be aware that the acquisition sequence hard-resets the target.
 @end deffn
 
-@deffn {Config Command} {kitprog_serial} serial
-Select a KitProg device by its @var{serial}. If left unspecified, the first
-device detected by OpenOCD will be used.
-@end deffn
-
 @deffn {Command} {kitprog acquire_psoc}
 Run a PSoC acquisition sequence immediately. Typically, this should not be used
 outside of the target-specific configuration scripts since it hard-resets the
@@ -3030,9 +3004,6 @@ parport cable wiggler
 
 @deffn {Interface Driver} {presto}
 ASIX PRESTO USB JTAG programmer.
-@deffn {Config Command} {presto serial} serial_string
-Configures the USB serial number of the Presto device to use.
-@end deffn
 @end deffn
 
 @deffn {Interface Driver} {rlink}
@@ -3164,11 +3135,6 @@ LaunchPad evaluation boards. The XDS110 is also available as a stand-alone USB
 debug probe with the added capability to supply power to the target board. The
 following commands are supported by the XDS110 driver:
 
-@deffn {Config Command} {xds110 serial} serial_string
-Specifies the serial number of which XDS110 probe to use. Otherwise, the first
-XDS110 found will be used.
-@end deffn
-
 @deffn {Config Command} {xds110 supply} voltage_in_millivolts
 Available only on the XDS110 stand-alone probe. Sets the voltage level of the
 XDS110 power supply. A value of 0 leaves the supply off. Otherwise, the supply