X-Git-Url: https://review.openocd.org/gitweb?p=openocd.git;a=blobdiff_plain;f=src%2Ftcl%2Fboard%2Fzy1000.cfg;fp=src%2Ftcl%2Fboard%2Fzy1000.cfg;h=0000000000000000000000000000000000000000;hp=d8bb46502f74c2186d68bfe731228c97f61a35fd;hb=dbbc9c41f7db210b0a4e226540a28e0a8a5019bf;hpb=140d6c8e7948710a764965075bfaa700efd09802

diff --git a/src/tcl/board/zy1000.cfg b/src/tcl/board/zy1000.cfg
deleted file mode 100644
index d8bb46502f..0000000000
--- a/src/tcl/board/zy1000.cfg
+++ /dev/null
@@ -1,110 +0,0 @@
-#Script for ZY1000
-
-#Atmel ties SRST & TRST together, at which point it makes
-#no sense to use TRST, but use TMS instead.
-#
-#The annoying thing with tying SRST & TRST together is that
-#there is no way to halt the CPU *before and during* the
-#SRST reset, which means that the CPU will run a number
-#of cycles before it can be halted(as much as milliseconds).
-reset_config srst_only srst_pulls_trst
-
-
-if { [info exists CHIPNAME] } {	
-   set  _CHIPNAME $CHIPNAME    
-} else {	 
-   set  _CHIPNAME zy1000
-}
-
-if { [info exists ENDIAN] } {	
-   set  _ENDIAN $ENDIAN    
-} else {	 
-   set  _ENDIAN little
-}
-
- 
-#jtag scan chain
-if { [info exists CPUTAPID ] } {
-   set _CPUTAPID $CPUTAPID
-} else {
-   set _CPUTAPID 0x1f0f0f0f
-}
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
-target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4
-
-# at CPU CLK <32kHz this must be disabled
-arm7_9 fast_memory_access enable
-arm7_9 dcc_downloads enable
-
-flash bank ecosflash 0x01000000 0x200000 2 2 0 ecos/at91eb40a.elf
-$_TARGETNAME configure -event reset-init { 
-	# Set up chip selects & timings
-	mww 0xFFE00000 0x0100273D
-	mww 0xFFE00004 0x08002125
-	mww 0xFFEe0008 0x02002125
-	mww 0xFFE0000c 0x03002125
-	mww 0xFFE00010 0x40000000
-	mww 0xFFE00014 0x50000000
-	mww 0xFFE00018 0x60000000
-	mww 0xFFE0001c 0x70000000
-	mww 0xFFE00020 0x00000001
-	mww 0xFFE00024 0x00000000
-	
-	# remap  
-	mww 0xFFFFF124 0xFFFFFFFF  
-	mww 0xffff0010 0x100
-	mww 0xffff0034 0x100
-	
-	#disable 16x5x UART interrupts
-	mww 0x08020004 0
-}
-
-# required for usable performance. Used for lots of
-# other things than flash programming.
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00020000 -work-area-size 0x20000 -work-area-backup 0
-
-jtag_khz 16000
-
-
-proc production_info {} {
-	return "Serial number is official MAC number. Format XXXXXXXXXXXX"
-}
-
-# There is no return value from this procedure. If it is
-# successful it does not throw an exception
-#
-# Progress messages are output via puts 
-proc production {firmwarefile serialnumber} {
-	if {[string length $serialnumber]!=12} {
-		puts "Invalid serial number"
-		return
-	}
-
-	puts "Power cycling target"
-	power off
-	sleep 3000
-	power on
-	sleep 1000
-	reset init
-	flash write_image erase $firmwarefile 0x1000000 bin
-	verify_image $firmwarefile 0x1000000 bin
-
-	# Big endian... weee!!!!
-	puts "Setting MAC number to $serialnumber"	
-	flash fillw [expr 0x1030000-0x8] "0x[string range $serialnumber 2 3][string range $serialnumber 0 1]0000" 1
-	flash fillw [expr 0x1030000-0x4] "0x[string range $serialnumber 10 11][string range $serialnumber 8 9][string range $serialnumber 6 7][string range $serialnumber 4 5]" 1
-	puts "Production successful"
-} 
-
-
-proc production_test {} {
-	power on
-	sleep 1000
-	target_request debugmsgs enable
-	reset run
-	sleep 25000
-	target_request debugmsgs disable
-	return "See IP address above..."
-}