X-Git-Url: https://review.openocd.org/gitweb?p=openocd.git;a=blobdiff_plain;f=tcl%2Fboard%2Ftelo.cfg;h=126f388f2ad5eec26204b24ef235f548a8d35e0c;hp=29066f960668e49fa9e9a3f4fa161ec84a2ec68b;hb=101124c69af0cf1546e7f0aa2606e36c3c8743eb;hpb=642519649e9f8171f2c06260eb0280c8a060d4df

diff --git a/tcl/board/telo.cfg b/tcl/board/telo.cfg
index 29066f9606..126f388f2a 100644
--- a/tcl/board/telo.cfg
+++ b/tcl/board/telo.cfg
@@ -1,22 +1,22 @@
-source [find c100.cfg]
+source [find target/c100.cfg]
 # basic register defintion for C100
-source [find c100regs.tcl]
+source [find target/c100regs.tcl]
 # board-config info
-source [find c100config.tcl]
+source [find target/c100config.tcl]
 # C100 helper functions
-source [find c100helper.tcl]
+source [find target/c100helper.tcl]
 
 
 # Telo board & C100 support trst and srst
 # Note that libftd2xx.so tries to assert srst
 # which break this script
 # use libftdi.so library instead with this script
-# make the reset asserted to 
+# make the reset asserted to
 # allow RC circuit to discharge for: [ms]
-jtag_nsrst_assert_width 100
+adapter_nsrst_assert_width 100
 jtag_ntrst_assert_width 100
 # don't talk to JTAG after reset for: [ms]
-jtag_nsrst_delay 100
+adapter_nsrst_delay 100
 jtag_ntrst_delay 100
 reset_config trst_and_srst separate
 
@@ -26,35 +26,36 @@ reset_config trst_and_srst separate
 # issue telnet: reset init
 # issue gdb: monitor reset init
 $_TARGETNAME configure -event reset-init {
-	jtag_khz 100
+	adapter_khz 100
 	# this will setup Telo board
 	setupTelo
 	#turn up the JTAG speed
-	jtag_khz 3000
-	puts "JTAG speek now 3MHz"
-	puts "type helpC100 to get help on C100"
+	adapter_khz 3000
+	echo "JTAG speek now 3MHz"
+	echo "type helpC100 to get help on C100"
 }
 
 $_TARGETNAME configure -event reset-deassert-post {
 	# Force target into ARM state.
-#	soft_reset_halt # not implemented on ARM11
-	puts "Detected SRSRT asserted on C100.CPU"
-	
+#	soft_reset_halt ;# not implemented on ARM11
+	echo "Detected SRSRT asserted on C100.CPU"
+
 }
 
 $_TARGETNAME configure -event reset-assert-post {
-  puts "Assering reset"
+  echo "Assering reset"
   #sleep 10
 }
 
-proc power_restore {} { puts "Sensed power restore. No action." } 
-proc srst_deasserted {} { puts "Sensed nSRST deasserted. No action." }
+proc power_restore {} { echo "Sensed power restore. No action." }
+proc srst_deasserted {} { echo "Sensed nSRST deasserted. No action." }
 
 
 # boots from NOR on CS0:  8 MBytes CFI flash, 16-bit bus
 # it's really 16MB but the upper 8mb is controller via gpio
 # openocd does not support 'complex reads/writes' to NOR
-flash bank cfi 0x20000000 0x01000000 2 2 $_TARGETNAME
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME cfi 0x20000000 0x01000000 2 2 $_TARGETNAME
 
 # writing data to memory does not work without this
-memwrite burst disable
\ No newline at end of file
+arm11 memwrite burst disable