X-Git-Url: https://review.openocd.org/gitweb?p=openocd.git;a=blobdiff_plain;f=tcl%2Fboard%2Funknown_at91sam9260.cfg;h=de49a69f567ab58e71305e1cc042238eea2c5436;hp=7286a9670f5518a4bf329654e21268405ffb33b2;hb=101124c69af0cf1546e7f0aa2606e36c3c8743eb;hpb=fcf1301e5269fdf734946ccf03177511f2eda851

diff --git a/tcl/board/unknown_at91sam9260.cfg b/tcl/board/unknown_at91sam9260.cfg
index 7286a9670f..de49a69f56 100644
--- a/tcl/board/unknown_at91sam9260.cfg
+++ b/tcl/board/unknown_at91sam9260.cfg
@@ -18,51 +18,51 @@ $_TARGETNAME configure -event reset-start {
         jtag_rclk 3
         halt
 	# RSTC_MR : enable user reset, MMU may be enabled... use physical address
-        arm926ejs mww phys 0xfffffd08 0xa5000501
+        mww phys 0xfffffd08 0xa5000501
 }
 
 
 $_TARGETNAME configure -event reset-init {
-        mww 0xfffffd44 0x00008000         # WDT_MR : disable watchdog
-
-	mww 0xfffffc20 0x00004001         # CKGR_MOR : enable the main oscillator
-        sleep 20                          # wait 20 ms
-        mww 0xfffffc30 0x00000001         # PMC_MCKR : switch to main oscillator
-        sleep 10                          # wait 10 ms
-        mww 0xfffffc28 0x205dbf09         # CKGR_PLLAR: Set PLLA Register for 192.512MHz
-        sleep 20                          # wait 20 ms
-        mww 0xfffffc30 0x00000101         # PMC_MCKR : Select prescaler (divide by 2)
-        sleep 10                          # wait 10 ms
-        mww 0xfffffc30 0x00000102         # PMC_MCKR : Clock from PLLA is selected (96.256 MHz)
-        sleep 10                          # wait 10 ms
+        mww 0xfffffd44 0x00008000         ;# WDT_MR : disable watchdog
+
+	mww 0xfffffc20 0x00004001         ;# CKGR_MOR : enable the main oscillator
+        sleep 20                          ;# wait 20 ms
+        mww 0xfffffc30 0x00000001         ;# PMC_MCKR : switch to main oscillator
+        sleep 10                          ;# wait 10 ms
+        mww 0xfffffc28 0x205dbf09         ;# CKGR_PLLAR: Set PLLA Register for 192.512MHz
+        sleep 20                          ;# wait 20 ms
+        mww 0xfffffc30 0x00000101         ;# PMC_MCKR : Select prescaler (divide by 2)
+        sleep 10                          ;# wait 10 ms
+        mww 0xfffffc30 0x00000102         ;# PMC_MCKR : Clock from PLLA is selected (96.256 MHz)
+        sleep 10                          ;# wait 10 ms
 
 	# Increase JTAG Speed to 6 MHz if RCLK is not supported
         jtag_rclk 6000
 
-	arm7_9 dcc_downloads enable       # Enable faster DCC downloads
+	arm7_9 dcc_downloads enable       ;# Enable faster DCC downloads
 
-	mww 0xffffec00 0x01020102         # SMC_SETUP0 : Setup SMC for Intel NOR Flash JS28F128P30T85 128MBit
-	mww 0xffffec04 0x09070806         # SMC_PULSE0
-	mww 0xffffec08 0x000d000b         # SMC_CYCLE0
-	mww 0xffffec0c 0x00001003         # SMC_MODE0
+	mww 0xffffec00 0x01020102         ;# SMC_SETUP0 : Setup SMC for Intel NOR Flash JS28F128P30T85 128MBit
+	mww 0xffffec04 0x09070806         ;# SMC_PULSE0
+	mww 0xffffec08 0x000d000b         ;# SMC_CYCLE0
+	mww 0xffffec0c 0x00001003         ;# SMC_MODE0
 
-	flash probe 0                     # Identify flash bank 0
+	flash probe 0                     ;# Identify flash bank 0
 
-	mww 0xfffff870 0xffff0000         # PIO_ASR  : Select peripheral function for D15..D31
-        mww 0xfffff804 0xffff0000         # PIO_PDR  : Disable PIO function for D15..D31
-        mww 0xfffff860 0xffff0000         # PIO_PUDR : Disable D15..D31 pull-ups
+	mww 0xfffff870 0xffff0000         ;# PIO_ASR  : Select peripheral function for D15..D31
+        mww 0xfffff804 0xffff0000         ;# PIO_PDR  : Disable PIO function for D15..D31
+        mww 0xfffff860 0xffff0000         ;# PIO_PUDR : Disable D15..D31 pull-ups
 
-        mww 0xffffef1c 0x00010102         # EBI_CSA  : Assign EBI Chip Select 1 to SDRAM
-                                          #            VDDIOMSEL set for +3V3 memory
-                                          #            Disable D0..D15 pull-ups
+        mww 0xffffef1c 0x00010102         ;# EBI_CSA  : Assign EBI Chip Select 1 to SDRAM
+                                           #            VDDIOMSEL set for +3V3 memory
+                                           #            Disable D0..D15 pull-ups
 
-	mww 0xffffea08 0x85227259         # SDRAMC_CR : Configure SDRAM (2 x Samsung K4S561632H-UC75 : 4M x 16Bit x 4 Banks)
+	mww 0xffffea08 0x85227259         ;# SDRAMC_CR : Configure SDRAM (2 x Samsung K4S561632H-UC75 : 4M x 16Bit x 4 Banks)
 
-	mww 0xffffea00 0x1                # SDRAMC_MR : issue a NOP command
+	mww 0xffffea00 0x1                ;# SDRAMC_MR : issue a NOP command
 	mww 0x20000000 0
-	mww 0xffffea00 0x2                # SDRAMC_MR : issue an 'All Banks Precharge' command
+	mww 0xffffea00 0x2                ;# SDRAMC_MR : issue an 'All Banks Precharge' command
 	mww 0x20000000 0
-	mww 0xffffea00 0x4                # SDRAMC_MR : issue 8 x 'Auto-Refresh' Command
+	mww 0xffffea00 0x4                ;# SDRAMC_MR : issue 8 x 'Auto-Refresh' Command
 	mww 0x20000000 0
 	mww 0xffffea00 0x4
 	mww 0x20000000 0
@@ -78,11 +78,11 @@ $_TARGETNAME configure -event reset-init {
 	mww 0x20000000 0
 	mww 0xffffea00 0x4
 	mww 0x20000000 0
-	mww 0xffffea00 0x3                # SDRAMC_MR : issue a 'Load Mode Register' command
+	mww 0xffffea00 0x3                ;# SDRAMC_MR : issue a 'Load Mode Register' command
 	mww 0x20000000 0
-	mww 0xffffea00 0x0                # SDRAMC_MR : normal mode
+	mww 0xffffea00 0x0                ;# SDRAMC_MR : normal mode
 	mww 0x20000000 0
-	mww 0xffffea04 0x2a2              # SDRAMC_TR : Set refresh timer count to 7us
+	mww 0xffffea04 0x2a2              ;# SDRAMC_TR : Set refresh timer count to 7us
 }
 
 
@@ -90,7 +90,8 @@ $_TARGETNAME configure -event reset-init {
 # Flash configuration
 #####################
 
-#flash bank cfi <base> <size> <chip width> <bus width> <target#>
-flash bank cfi 0x10000000 0x01000000 2 2 0
+#flash bank <name> cfi <base> <size> <chip width> <bus width> <target>
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME cfi 0x10000000 0x01000000 2 2 $_TARGETNAME