X-Git-Url: https://review.openocd.org/gitweb?p=openocd.git;a=blobdiff_plain;f=tcl%2Ftarget%2Fmarvell%2Fcn9130.cfg;fp=tcl%2Ftarget%2Fmarvell%2Fcn9130.cfg;h=23e472f2840d45c95602cb410ee33d8dadcc3e47;hp=0000000000000000000000000000000000000000;hb=65fc586d6ee18813937ec0fdb264b9e0d4bc1c76;hpb=8d3728f931888d2e9a9bc5a31d26c8327649e676

diff --git a/tcl/target/marvell/cn9130.cfg b/tcl/target/marvell/cn9130.cfg
new file mode 100644
index 0000000000..23e472f284
--- /dev/null
+++ b/tcl/target/marvell/cn9130.cfg
@@ -0,0 +1,178 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+
+# cn9130 -- support for the Marvell Octeon TX2 / CN9130 CPU family
+#
+# henrik.nordstorm@addiva.se, Nov 2023
+
+if { [info exists CHIPNAME] } {
+   set _CHIPNAME $CHIPNAME
+} else {
+   set _CHIPNAME cn9130
+}
+
+if { [info exists MASTERTAPID] } {
+   set _MASTERTAPID $MASTERTAPID
+} else {
+   set _MASTERTAPID 0x07025357
+}
+
+if { [info exists APTAPID] } {
+   set _APTAPID $APTAPID
+} else {
+   set _APTAPID 0x4ba00477
+}
+
+if { [info exists SBTAPID] } {
+   set _SBTAPID $SBTAPID
+} else {
+   set _SBTAPID 0x4ba00477
+}
+
+if { [info exists CORES] } {
+   set _CORES $CORES
+} else {
+   set _CORES 4
+}
+
+# CTI base address should be possible to read from the CoreSight
+# ROM table like how the DBG base address is when not specified.
+if { [info exists CTIBASE] } {
+   set _CTIBASE $CTIBASE
+} else {
+   set _CTIBASE {0x80420000 0x80520000 0x80620000 0x80720000}
+}
+
+# CN9130 is a multi-die chip and has a multi level hierarchical
+# JTAG TAP, where all the DAPs are disabled at reset, requiring
+# both configuration to enable access to the chip DAPs, and a
+# vendor specific bypass IR instruction to access the slave TAPs
+# via the master TAP. In addition there is a number of sample
+# bits that should be ignored.
+#
+# The default BYPASS instruction in the master TAP bypasses the
+# whole chip and not only the master TAP. And similarly on
+# IDCODE the master TAP only responds with it's own ID and
+# bypasses the other TAPs on the chip, while OpenOCD expects
+# ID from all enabled TAPs in the chain.
+
+# Bootstrap with the default boundary scan oriented TAP configuration
+# where the master,ap,sb TAPs are seen as one big fat TAP, which matches
+# what OpenOCD expects from IDCODE and BYPASS.
+
+jtag newtap $_CHIPNAME bs  -irlen 19 -enable -expected-id $_MASTERTAPID
+
+# Declare the full JTAG chain, but in disabled state during setup
+
+jtag newtap $_CHIPNAME sample4 -irlen 1 -disable
+jtag newtap $_CHIPNAME sample3 -irlen 1 -disable
+jtag newtap $_CHIPNAME sample2 -irlen 1 -disable
+jtag newtap $_CHIPNAME ap.cpu  -irlen 4 -disable -expected-id $_APTAPID
+jtag newtap $_CHIPNAME ap      -irlen 5 -disable
+jtag newtap $_CHIPNAME sample1 -irlen 1 -disable
+jtag newtap $_CHIPNAME sb.cpu  -irlen 4 -disable -expected-id $_SBTAPID
+jtag newtap $_CHIPNAME sb      -irlen 5 -disable
+jtag newtap $_CHIPNAME master  -irlen 5 -disable -ir-bypass 0x11 -expected-id $_MASTERTAPID
+
+# Once the iniial IDCODE scan has completed switch to more detailed
+# scan chain giving access to the individual chip TAPs.
+
+jtag configure $_CHIPNAME.bs -event setup "cn9130_enable_full_chain $_CHIPNAME"
+
+proc cn9130_enable_full_chain { _CHIPNAME } {
+   # Switch to detailed TAP declaration
+   jtag tapdisable $_CHIPNAME.bs
+   jtag tapenable $_CHIPNAME.master
+   jtag tapenable $_CHIPNAME.sb
+   jtag tapenable $_CHIPNAME.sample1
+   jtag tapenable $_CHIPNAME.ap
+   jtag tapenable $_CHIPNAME.sample2
+   jtag tapenable $_CHIPNAME.sample3
+   jtag tapenable $_CHIPNAME.sample4
+}
+
+# AP & SB TAPs have a config register to enable/disable access to
+# the auxilary DAP TAP. Default off which hides the DAP TAP from
+# the scan chain.
+proc cn9130_dap_config { chip tap state } {
+   irscan $chip.$tap 0x12
+   drscan $chip.$tap 32 $state
+}
+
+jtag configure $_CHIPNAME.bs -event tap-disable ""
+jtag configure $_CHIPNAME.bs -event tap-enable ""
+jtag configure $_CHIPNAME.sample4 -event tap-enable ""
+jtag configure $_CHIPNAME.sample3 -event tap-enable ""
+jtag configure $_CHIPNAME.sample2 -event tap-enable ""
+jtag configure $_CHIPNAME.ap.cpu -event tap-disable "cn9130_dap_config $_CHIPNAME ap 0"
+jtag configure cn9130.ap.cpu -event tap-enable "cn9130_dap_config $_CHIPNAME ap 1"
+jtag configure $_CHIPNAME.ap -event tap-enable ""
+jtag configure $_CHIPNAME.sample1 -event tap-enable ""
+jtag configure $_CHIPNAME.sb.cpu -event tap-disable "cn9130_dap_config $_CHIPNAME sb 0"
+jtag configure cn9130.sb.cpu -event tap-enable "cn9130_dap_config $_CHIPNAME sb 1"
+jtag configure $_CHIPNAME.sb -event tap-enable ""
+jtag configure $_CHIPNAME.master -event tap-enable ""
+
+dap create $_CHIPNAME.ap.dap -chain-position $_CHIPNAME.ap.cpu
+
+# Main bus
+target create $_CHIPNAME.ap.axi mem_ap \
+   -dap $_CHIPNAME.ap.dap \
+   -ap-num 0
+
+# Periperials bus
+target create $_CHIPNAME.ap.apb mem_ap \
+   -dap $_CHIPNAME.ap.dap \
+   -ap-num 1
+
+# MSS bus
+target create $_CHIPNAME.ap.ahb mem_ap \
+   -dap $_CHIPNAME.ap.dap \
+   -ap-num 2
+
+# AP A72 CPU cores
+set _smp_command ""
+for { set _core 0 } { $_core < $_CORES } { incr _core 1 } {
+   cti create $_CHIPNAME.ap.cti.$_core \
+      -dap $_CHIPNAME.ap.dap \
+      -baseaddr [ lindex $_CTIBASE $_core ]  \
+      -ap-num 1
+
+   if { $_core == 0 } {
+      target create $_CHIPNAME.ap.a72.$_core aarch64 \
+         -dap $_CHIPNAME.ap.dap \
+         -ap-num 1 \
+         -cti $_CHIPNAME.ap.cti.$_core \
+         -coreid $_core \
+         -rtos hwthread
+      set _smp_command "target smp $_CHIPNAME.ap.a72.$_core"
+   } else {
+      # Defer non-boot cores. Held hard in reset until
+      # SMP is activated.
+      target create $_CHIPNAME.ap.a72.$_core aarch64 \
+         -dap $_CHIPNAME.ap.dap \
+         -ap-num 1 \
+         -cti $_CHIPNAME.ap.cti.$_core \
+         -coreid $_core \
+         -defer-examine
+      set _smp_command "$_smp_command $_CHIPNAME.ap.a72.$_core"
+   }
+
+}
+
+# Set up the A72 cluster as SMP
+# Note: Only the boot core is active by default. The other core DAPs can
+# be enabled by arp_examine after they have been released from hard reset.
+eval $_smp_command
+
+# AP MSS M3 CPU core. Defer as it is held in reset until firmware is loaded.
+target create $_CHIPNAME.ap.mss cortex_m -dap $_CHIPNAME.ap.dap -ap-num 2 -defer-examine
+
+# Why is this needed? reset fails with "Debug regions are unpowered" otherwise
+$_CHIPNAME.ap.axi configure -event examine-start "dap init"
+
+# Automate enabling the AP A72 DAP once the full scan chain is enabled
+proc cn9130_ap_setup { _CHIPNAME } {
+   jtag tapenable $_CHIPNAME.ap.cpu
+   targets $_CHIPNAME.ap.a72.0
+}
+jtag configure $_CHIPNAME.ap -event setup "cn9130_ap_setup $_CHIPNAME"