X-Git-Url: https://review.openocd.org/gitweb?p=openocd.git;a=blobdiff_plain;f=tcl%2Ftarget%2Fstm32f4x.cfg;h=73b1dc8eda447150ff6c29ae0076f05060363b96;hp=ecd39de77ca5e82070364738007d4c26b7fb75bb;hb=2231da8ec4e7d7ae9b652f3dd1a7104f5a110f3f;hpb=41a968ec055c309d2eb669c20f831e169b4dc2e2

diff --git a/tcl/target/stm32f4x.cfg b/tcl/target/stm32f4x.cfg
index ecd39de77c..73b1dc8eda 100644
--- a/tcl/target/stm32f4x.cfg
+++ b/tcl/target/stm32f4x.cfg
@@ -4,6 +4,7 @@
 # stm32 devices support both JTAG and SWD transports.
 #
 source [find target/swj-dp.tcl]
+source [find mem_helper.tcl]
 
 if { [info exists CHIPNAME] } {
    set _CHIPNAME $CHIPNAME
@@ -11,18 +12,14 @@ if { [info exists CHIPNAME] } {
    set _CHIPNAME stm32f4x
 }
 
-if { [info exists ENDIAN] } {
-   set _ENDIAN $ENDIAN
-} else {
-   set _ENDIAN little
-}
+set _ENDIAN little
 
 # Work-area is a space in RAM used for flash programming
-# By default use 64kB
+# By default use 32kB (Available RAM in smallest device STM32F410)
 if { [info exists WORKAREASIZE] } {
    set _WORKAREASIZE $WORKAREASIZE
 } else {
-   set _WORKAREASIZE 0x10000
+   set _WORKAREASIZE 0x8000
 }
 
 #jtag scan chain
@@ -39,55 +36,72 @@ if { [info exists CPUTAPID] } {
 }
 
 swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-if { [info exists BSTAPID] } {
-   set _BSTAPID $BSTAPID
-} else {
-  # See STM Document RM0090
-  # Section 38.6.2
-  # STM32F405xx/07xx and STM32F415xx/17xx
-  set _BSTAPID1 0x06413041
-  # STM32F42xxx and STM32F43xxx
-  set _BSTAPID2 0x06419041
-  # See STM Document RM0368 (Rev. 3)
-  # STM32F401B/C
-  set _BSTAPID3 0x06423041
-  # STM32F401D/E
-  set _BSTAPID4 0x06433041
-  # See STM Document RM0383 (Rev 2)
-  # STM32F411
-  set _BSTAPID5 0x06431041
-}
+dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
 
 if {[using_jtag]} {
- swj_newdap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
-     -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \
-     -expected-id $_BSTAPID4 -expected-id $_BSTAPID5
+   jtag newtap $_CHIPNAME bs -irlen 5
 }
 
 set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
+target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
 
 $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
 
 set _FLASHNAME $_CHIPNAME.flash
 flash bank $_FLASHNAME stm32f2x 0 0 0 0 $_TARGETNAME
 
-# JTAG speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz
+# JTAG speed should be <= F_CPU/6. F_CPU after reset is 16MHz, so use F_JTAG = 2MHz
 #
 # Since we may be running of an RC oscilator, we crank down the speed a
 # bit more to be on the safe side. Perhaps superstition, but if are
 # running off a crystal, we can run closer to the limit. Note
 # that there can be a pretty wide band where things are more or less stable.
-adapter_khz 1000
+adapter_khz 2000
 
 adapter_nsrst_delay 100
 if {[using_jtag]} {
  jtag_ntrst_delay 100
 }
 
+reset_config srst_nogate
+
 if {![using_hla]} {
    # if srst is not fitted use SYSRESETREQ to
    # perform a soft reset
    cortex_m reset_config sysresetreq
 }
+
+$_TARGETNAME configure -event examine-end {
+	# Enable debug during low power modes (uses more power)
+	# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
+	mmw 0xE0042004 0x00000007 0
+
+	# Stop watchdog counters during halt
+	# DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
+	mmw 0xE0042008 0x00001800 0
+}
+
+$_TARGETNAME configure -event trace-config {
+	# Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
+	# change this value accordingly to configure trace pins
+	# assignment
+	mmw 0xE0042004 0x00000020 0
+}
+
+$_TARGETNAME configure -event reset-init {
+	# Configure PLL to boost clock to HSI x 4 (64 MHz)
+	mww 0x40023804 0x08012008   ;# RCC_PLLCFGR 16 Mhz /8 (M) * 128 (N) /4(P)
+	mww 0x40023C00 0x00000102   ;# FLASH_ACR = PRFTBE | 2(Latency)
+	mmw 0x40023800 0x01000000 0 ;# RCC_CR |= PLLON
+	sleep 10                    ;# Wait for PLL to lock
+	mmw 0x40023808 0x00001000 0 ;# RCC_CFGR |= RCC_CFGR_PPRE1_DIV2
+	mmw 0x40023808 0x00000002 0 ;# RCC_CFGR |= RCC_CFGR_SW_PLL
+
+	# Boost JTAG frequency
+	adapter_khz 8000
+}
+
+$_TARGETNAME configure -event reset-start {
+	# Reduce speed since CPU speed will slow down to 16MHz with the reset
+	adapter_khz 2000
+}