Most hardware development boards have a UART, a real serial port, or a virtual USB serial device, so this driver
allows you to start building your own JTAG adapter without the complexity of a custom USB connection.
-@deffn {Config Command} {buspirate_port} serial_port
+@deffn {Config Command} {buspirate port} serial_port
Specify the serial port's filename. For example:
@example
-buspirate_port /dev/ttyUSB0
+buspirate port /dev/ttyUSB0
@end example
@end deffn
-@deffn {Config Command} {buspirate_speed} (normal|fast)
+@deffn {Config Command} {buspirate speed} (normal|fast)
Set the communication speed to 115k (normal) or 1M (fast). For example:
@example
-buspirate_mode normal
+buspirate mode normal
@end example
@end deffn
-@deffn {Config Command} {buspirate_mode} (normal|open-drain)
+@deffn {Config Command} {buspirate mode} (normal|open-drain)
Set the Bus Pirate output mode.
@itemize @minus
@item In normal mode (push/pull), do not enable the pull-ups, and do not connect I/O header pin VPU to JTAG VREF.
@end itemize
For example:
@example
-buspirate_mode normal
+buspirate mode normal
@end example
@end deffn
-@deffn {Config Command} {buspirate_pullup} (0|1)
+@deffn {Config Command} {buspirate pullup} (0|1)
Whether to connect (1) or not (0) the I/O header pin VPU (JTAG VREF)
to the pull-up/pull-down resistors on MOSI (JTAG TDI), CLK (JTAG TCK), MISO (JTAG TDO) and CS (JTAG TMS).
For example:
@example
-buspirate_pullup 0
+buspirate pullup 0
@end example
@end deffn
-@deffn {Config Command} {buspirate_vreg} (0|1)
+@deffn {Config Command} {buspirate vreg} (0|1)
Whether to enable (1) or disable (0) the built-in voltage regulator,
which can be used to supply power to a test circuit through
I/O header pins +3V3 and +5V. For example:
@example
-buspirate_vreg 0
+buspirate vreg 0
@end example
@end deffn
-@deffn {Command} {buspirate_led} (0|1)
+@deffn {Command} {buspirate led} (0|1)
Turns the Bus Pirate's LED on (1) or off (0). For example:
@end deffn
@example
-buspirate_led 1
+buspirate led 1
@end example
@end deffn
}
-static const struct command_registration buspirate_command_handlers[] = {
+static const struct command_registration buspirate_subcommand_handlers[] = {
{
- .name = "buspirate_adc",
+ .name = "adc",
.handler = &buspirate_handle_adc_command,
.mode = COMMAND_EXEC,
.help = "reads voltages on adc pins",
.usage = "",
},
{
- .name = "buspirate_vreg",
+ .name = "vreg",
.usage = "<1|0>",
.handler = &buspirate_handle_vreg_command,
.mode = COMMAND_CONFIG,
.help = "changes the state of voltage regulators",
},
{
- .name = "buspirate_pullup",
+ .name = "pullup",
.usage = "<1|0>",
.handler = &buspirate_handle_pullup_command,
.mode = COMMAND_CONFIG,
.help = "changes the state of pullup",
},
{
- .name = "buspirate_led",
+ .name = "led",
.usage = "<1|0>",
.handler = &buspirate_handle_led_command,
.mode = COMMAND_EXEC,
.help = "changes the state of led",
},
{
- .name = "buspirate_speed",
+ .name = "speed",
.usage = "<normal|fast>",
.handler = &buspirate_handle_speed_command,
.mode = COMMAND_CONFIG,
.help = "speed of the interface",
},
{
- .name = "buspirate_mode",
+ .name = "mode",
.usage = "<normal|open-drain>",
.handler = &buspirate_handle_mode_command,
.mode = COMMAND_CONFIG,
.help = "pin mode of the interface",
},
{
- .name = "buspirate_port",
+ .name = "port",
.usage = "/dev/ttyUSB0",
.handler = &buspirate_handle_port_command,
.mode = COMMAND_CONFIG,
COMMAND_REGISTRATION_DONE
};
+static const struct command_registration buspirate_command_handlers[] = {
+ {
+ .name = "buspirate",
+ .mode = COMMAND_ANY,
+ .help = "perform buspirate management",
+ .chain = buspirate_subcommand_handlers,
+ .usage = "",
+ },
+ COMMAND_REGISTRATION_DONE
+};
+
static const struct swd_driver buspirate_swd = {
.init = buspirate_swd_init,
.switch_seq = buspirate_swd_switch_seq,
eval sysfsgpio swdio_num $args
}
+lappend _telnet_autocomplete_skip buspirate_adc
+proc buspirate_adc args {
+ echo "DEPRECATED! use 'buspirate adc' not 'buspirate_adc'"
+ eval buspirate adc $args
+}
+
+lappend _telnet_autocomplete_skip buspirate_vreg
+proc buspirate_vreg args {
+ echo "DEPRECATED! use 'buspirate vreg' not 'buspirate_vreg'"
+ eval buspirate vreg $args
+}
+
+lappend _telnet_autocomplete_skip buspirate_pullup
+proc buspirate_pullup args {
+ echo "DEPRECATED! use 'buspirate pullup' not 'buspirate_pullup'"
+ eval buspirate pullup $args
+}
+
+lappend _telnet_autocomplete_skip buspirate_led
+proc buspirate_led args {
+ echo "DEPRECATED! use 'buspirate led' not 'buspirate_led'"
+ eval buspirate led $args
+}
+
+lappend _telnet_autocomplete_skip buspirate_speed
+proc buspirate_speed args {
+ echo "DEPRECATED! use 'buspirate speed' not 'buspirate_speed'"
+ eval buspirate speed $args
+}
+
+lappend _telnet_autocomplete_skip buspirate_mode
+proc buspirate_mode args {
+ echo "DEPRECATED! use 'buspirate mode' not 'buspirate_mode'"
+ eval buspirate mode $args
+}
+
+lappend _telnet_autocomplete_skip buspirate_port
+proc buspirate_port args {
+ echo "DEPRECATED! use 'buspirate port' not 'buspirate_port'"
+ eval buspirate port $args
+}
+
# END MIGRATION AIDS