From: Oleksij Rempel Date: Thu, 22 Feb 2018 08:42:59 +0000 (+0100) Subject: tcl/target: add Allwinner V3s SoC support X-Git-Tag: v0.11.0-rc1~1021 X-Git-Url: https://review.openocd.org/gitweb?p=openocd.git;a=commitdiff_plain;h=f8367dbb4976474ac0a99f20b8028a1721f0c82e tcl/target: add Allwinner V3s SoC support Change-Id: I2459d2b137050985b7301047f9651951d72d9e9e Signed-off-by: Oleksij Rempel Reviewed-on: http://openocd.zylin.com/4427 Tested-by: jenkins Reviewed-by: Paul Fertser --- diff --git a/tcl/target/allwinner_v3s.cfg b/tcl/target/allwinner_v3s.cfg new file mode 100644 index 0000000000..32fd188729 --- /dev/null +++ b/tcl/target/allwinner_v3s.cfg @@ -0,0 +1,71 @@ +# This is the config for an Allwinner V3/V3s (sun8iw8). +# +# Notes: +# - Single core ARM Cortex-A7 with a maximum frequency of 1.2 GHz. +# - Thumb-2 Technology +# - Support NEON Advanced SIMD(Single Instruction Multiple Data)instruction +# for acceleration of media and signal processing functions +# - Support Large Physical Address Extensions(LPAE) +# - VFPv4 Floating Point Unit +# - 32KB L1 Instruction cache and 32KB L1 Data cache +# - 128KB L2 cache +# - has some integrated DDR2 RAM. +# +# Pins related for debug and bootstrap: +# JTAG +# JTAG_TMS PF0, SDC0_D1 +# JTAG_TDI PF1, SDC0_D0 +# JTAG_TDO PF3, SDC0_CMD +# JTAG_TCK PF5, SDC0_D2 +# UART +# None of UART ports seems to be enabled by ROM. +# UART0_TX PF2, SDC0_CLK Per default disabled +# UART0_RX PF4, SDC0_D3 Per default disabled +# UART1_TX PE21 Per default disabled +# UART1_RX PE22 Per default disabled +# UART2_TX PB0 Per default disabled +# UART2_RX PB1 Per default disabled +# +# JTAG is enabled by default after power on on listed JTAG_* pins. So far the +# boot sequence is: +# Time Action +# 0000ms Power ON +# 0200ms JTAG enabled +# 0220ms JTAG pins switched to SD mode +# +# The time frame of 20ms can be not enough to init and halt the CPU. In this +# case I would recommend to set: "adapter_khz 15000" +# To get more or less precise timings, the board should provide reset pin, +# or some bench power supply with remote function. In my case I used +# EEZ H24005 with this command to power on and halt the target: +# "exec echo "*TRG" > /dev/ttyACM0; sleep 220; reset halt" +# After this it is possible to enable JTAG mode again from boot loader or OS. +# Following DAPs are available: +# dap[0]->MEM-AP AHB +# dap[1]->MEM-AP APB->CA7[0] +# + +if { [info exists CHIPNAME] } { + set _CHIPNAME $CHIPNAME +} else { + set _CHIPNAME v3s +} + +if { [info exists DAP_TAPID] } { + set _DAP_TAPID $DAP_TAPID +} else { + set _DAP_TAPID 0x5ba00477 +} + +# No NRST or SRST is present on the SoC. Boards may provide +# some sort of Power cycle reset for complete board or SoC. +# For this case we provide srst_pulls_trst so the board config +# only needs to set srst_only. +reset_config none srst_pulls_trst + +jtag newtap $_CHIPNAME dap -irlen 4 -ircapture 0x01 -irmask 0x0f \ + -expected-id $_DAP_TAPID + +# Add Cortex A7 core +set _TARGETNAME $_CHIPNAME.cpu +target create $_TARGETNAME cortex_a -chain-position $_CHIPNAME.dap