Paul Fertser [Tue, 10 Mar 2015 19:27:16 +0000 (22:27 +0300)]
tcl/board/twr-k60f120m: remove useless flash bank 0 definition
Since the very first flash bank is already defined in target/kx.cfg,
there's no sense in repeating it.
Reported and tested by Richard Braun.
Change-Id: I417b7072b5e6675ddbf824446e7581b8b7da8f4b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2595
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Tue, 10 Mar 2015 19:22:36 +0000 (22:22 +0300)]
flash/nor/kinetis: do not attempt mass-erase in place of a bank erase
Many kinetis parts come in multi-bank configuration, so this
optimisation here can't be performed safely.
Investigated and fixed by Richard Braun.
Change-Id: I2b56614b47951595c403a1a8edd3afe11b85679b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2594
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Tue, 10 Feb 2015 10:32:07 +0000 (13:32 +0300)]
armv7m_trace, stlink: provide APIs to capture trace with an adapter
Change-Id: I9d193dd5af382912e4fe838bd4f612cffd11b295
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2540
Tested-by: jenkins
Paul Fertser [Mon, 9 Feb 2015 14:04:52 +0000 (17:04 +0300)]
armv7m: add generic trace support (TPIU, ITM, etc.)
This provides support for various trace-related subsystems in a
generic and expandable way.
Change-Id: I3a27fa7b8cfb111753088bb8c3d760dd12d1395f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2538
Tested-by: jenkins
Uwe Bonnes [Mon, 9 Mar 2015 13:08:48 +0000 (14:08 +0100)]
stm32l1.cfg: Add missing dash to fix
f7394049d3 commit.
Change-Id: Ifeb2d4fc2b43813edbc6fe2cf08bfd4c55cd1e86
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2590
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Andreas Fritiofson [Thu, 3 Jul 2014 17:33:45 +0000 (19:33 +0200)]
tcl: Add default hooks for STM32F3x
Keep clocks running in low power modes. Stop watchdogs from interfering
with the debug session. Set up PLL and increase clock at reset init.
Change-Id: I984d2018f7d47a1042f1e12894563154fa7b566c
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2196
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Paul Fertser [Sat, 21 Feb 2015 07:55:41 +0000 (10:55 +0300)]
flash/nor/stellaris: allow to recover a locked device that can't be examined
Change-Id: I28536184053e2d1ba906620e728f7fad6ba39f0a
Reported-by: Ed Beroset <beroset@mindspring.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2552
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Ed Beroset <beroset@ieee.org>
Andreas Färber [Sat, 28 Feb 2015 01:39:44 +0000 (02:39 +0100)]
jlink: Add variant "J-Link Lite-XMC4000"
Avoids "J-Link hw type unknown 0x10" on the Infineon Relax Lite Kit.
Change-Id: I3091623ead2e84b67ac20d9866307ccbb3f26f66
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2568
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Andreas Färber [Sat, 28 Feb 2015 00:23:34 +0000 (01:23 +0100)]
jlink: Add variant "J-Link Lite-XMC4200"
Avoids "J-Link hw type unknown 0x11" on various Infineon boards.
Change-Id: If20b9e21110d2acc02be57f5faf28c5e6a39e2c9
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2565
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Wed, 11 Feb 2015 08:08:40 +0000 (11:08 +0300)]
server, target, cortex_m: add deinit_target to the API to free resources
This should facilitate dynamic target creation and removal.
Currently it helps with getting 0 bytes lost report from Valgrind on
exit (after talking to a nucleo board). However, 1,223,886 bytes in
5,268 blocks are still reachable which means the app holds pointers to
that data on exit. The majority comes from the jtag command queue,
there're also many blocks from TCL command registration.
Change-Id: I7523234bb90fffd26f7d29cdd7648ddd221d46ab
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2544
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Paul Fertser [Mon, 9 Feb 2015 13:43:58 +0000 (16:43 +0300)]
target/target: call event handlers around examine when polling resumes
The target might be using Tcl examine-start and examine-end handlers,
they need to be called when the target gets reexamined after polling
succeeds again.
Change-Id: I371380c6f3c427ec7a0206d73426f6589f18a9bd
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2536
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Paul Fertser [Wed, 11 Feb 2015 08:04:15 +0000 (11:04 +0300)]
hla/hla_interface: call HLA layout API close() on quit
This bug was exposed by Valgrind.
Change-Id: I2e2bc036b49ca3ff22f78f765ee4537763350096
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2543
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Wed, 11 Feb 2015 08:02:34 +0000 (11:02 +0300)]
target/cortex_m: do not leak memory on reexamination
This bug was exposed by Valgrind.
Change-Id: If50878664d928c0a44e309ca1452089c1ac71466
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2542
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Wed, 11 Feb 2015 07:51:17 +0000 (10:51 +0300)]
target: fix timer callbacks processing
Warning, behaviour change: before this patch if a timer callback
returned an error, the other handlers in the list were not called.
This patch fixes two different issues with the way timer callbacks are
called:
1. The function is not designed to be reentrant but a nested call is
possible via: target_handle timer event -> poll -> target events
before/after reexaminantion -> script_command_run ->
target_call_timer_callbacks_now . This patch makes function a no-op
when called recursively;
2. The current code can deal with the case when calling a handler
leads to its removal but not when it leads to removal of the next
callback in the list. This patch defers actual removal to consolidate
it with the calling loop.
These bugs were exposed by Valgrind.
Change-Id: Ia628a744634f5d2911eb329747e826cb9772e789
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2541
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Thu, 13 Mar 2014 09:27:45 +0000 (13:27 +0400)]
arm11: initialise DPM and register cache before reading DSCR for the first time
When target was already halted during the initial examination,
arm11_check_init() was trying to read, store and interpret DSCR
contents before the DPM structure is initialised. This caused
a segfault like described on
http://sourceforge.net/apps/trac/openocd/ticket/65 .
This is a totally untested attempt to fix this issue.
Change-Id: I2fff115679a3f0023e7a88c749ccb5f045d6cf01
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2043
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Sun, 15 Feb 2015 18:37:16 +0000 (21:37 +0300)]
stlink: avoid null pointer dereference in stlink_usb_close()
Otherwise it happens if stlink can not be opened on start.
Change-Id: I7088f10e61508dae230eccfe576a51498c92f5b8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2550
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Franck Jullien [Fri, 23 Jan 2015 13:09:14 +0000 (14:09 +0100)]
openrisc: add profiling function
Change-Id: Ifee89b289069590e6086a4713b165989578e29ec
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/2494
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Thu, 29 Jan 2015 10:58:45 +0000 (13:58 +0300)]
armv7m: do not access FPU registers when not present
This is runtime and valgrind tested with l0, l1 and f3 hla boards.
Change-Id: I49b0b042253d5f3bf216997f0203583db319fe23
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2516
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Sun, 1 Apr 2012 13:18:02 +0000 (15:18 +0200)]
armv7m: add FPU registers support
This patch adds the fpv4-sp-d16 registers to the armv7m register set.
The work is inspired by Mathias K but takes a different approach:
instead of having both double and single presicion registers in the
cache this patch works only with the doubles and counts on GDB to
split the data in halves whenever needed.
Tested with HLA only (on an STM32F334 disco board).
Currently this patch makes all ARMv7-M targets report an FPU-enabled
target description to GDB. It shouldn't harm if the user is not trying
to access non-existing FPU. However, the plan is to make this depend
on actual FPU presence later.
Change-Id: Ifcc72c80ef745230c42e4dc3995f792753fc4e7a
Signed-off-by: Mathias K <kesmtp@freenet.de>
[fercerpav@gmail.com: rework to fit target description framework]
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/514
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Sat, 31 Jan 2015 08:20:51 +0000 (11:20 +0300)]
jimtcl: update to 0.76 release version
It makes sense to use the latest released version to ensure
compatibility.
Change-Id: I0957f927d825fa6fb6a1594ca17bcca46ee6c1a6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2522
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
pierre Kuo [Fri, 13 Feb 2015 03:27:52 +0000 (11:27 +0800)]
target/arm_disassembler: add exception related disassembly
Add ERET/HVC/SMC disassebly decoding flow, below is testing result
> mdw 0x5c 4
0x0000005c:
e160006e e1400072 e1600073 ee110f10
> arm disassemble 0x5c 4
0x0000005c 0xe160006e ERET
0x00000060 0xe1400072 HVC 0x0002
0x00000064 0xe1600073 SMC 0x0003
0x00000068 0xee110f10 MRC p15, 0x00, r0, c1, c0, 0x00
>
Change-Id: I1beccff885b5b37747edd0b2e9fb2297ce466a00
Signed-off-by: pierre Kuo <vichy.kuo@gmail.com>
Reviewed-on: http://openocd.zylin.com/2548
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Thu, 26 Feb 2015 16:48:08 +0000 (19:48 +0300)]
target/cortex_a: remove dead assignment
Found by clang static checker.
Change-Id: I77b0dc18188328fdb28d07b9e5c52e06182d9e2b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2561
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Thu, 26 Feb 2015 16:42:08 +0000 (19:42 +0300)]
flash/nor/stellaris: remove dead assignment
Found by clang static checker.
Change-Id: Ifa58ba383092341c7343916e5cc8ec3c72ab2f60
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2560
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Thu, 26 Feb 2015 16:39:50 +0000 (19:39 +0300)]
flash/nor/sim3x: remove dead assignment
Found by clang static code checker.
Change-Id: Ic1370f8d7a48f08da6514afec5aacde38af7dfb6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2559
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Fri, 6 Feb 2015 15:28:56 +0000 (18:28 +0300)]
contrib/itmdump: fix UB in show_swit, and few compile warnings
Change-Id: I1c5c99f190f7b4d405dc6fa06533e7ff37a652ec
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2533
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Karl Palsson [Fri, 19 Dec 2014 14:20:40 +0000 (14:20 +0000)]
contrib: itmdump: fix incorrect format printf
Change-Id: I29100e4b284e031613586a66daa74987d86ac9e1
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2449
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Austin Morton [Sat, 21 Feb 2015 09:20:33 +0000 (04:20 -0500)]
server: tcl_notifications command
Implements async target notifications to the tcl server
Change-Id: I4d83e9fa209e95426c440030597f99e9f0c3b260
Signed-off-by: Austin Morton <austinpmorton@gmail.com>
Reviewed-on: http://openocd.zylin.com/2336
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Marian Cingel [Fri, 3 Oct 2014 12:15:16 +0000 (14:15 +0200)]
rtos: Freescale MQX rtos support
ARMv7E-M (CortexM4) architecture
- fix position offset of r2,r3 registers on exception stack
- switch 'calloc' arguments
- remove prototypes of internal function and typedefs
- add NULL check for alloc functions
- remove last line of license "Franklin Street, Fifth Floor"
because of 'checkpatch' validation
- environment: jlink + twrk60n512
Change-Id: I70840ded15b17dd945ca190ce31e2775078da2d9
Signed-off-by: Marian Cingel <cingel.marian@gmail.com>
Reviewed-on: http://openocd.zylin.com/2353
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Matthijs van Duin [Tue, 29 Jul 2014 06:24:29 +0000 (10:24 +0400)]
tcl/interface/ftdi/xdsv2: fix and clarify EMU* signals
The signal names are changed for consistency with TI's docs and
sources.
Change-Id: Ic5c5314daa20f6f610be8a848399f951d47aa137
Signed-off-by: Matthijs van Duin <matthijs@rinnic-vaude.nl>
Reviewed-on: http://openocd.zylin.com/2231
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Uwe Bonnes [Thu, 29 Jan 2015 11:03:23 +0000 (12:03 +0100)]
stm32l1.cfg: Add ID Code of Cat.2 devices.
Change-Id: I4eb5020858c1896e294d633213f3df3fa45b6250
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2517
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Uwe Bonnes [Mon, 23 Feb 2015 17:14:45 +0000 (18:14 +0100)]
stm32f3x.cfg: Remove duplicate item.
Change-Id: I812c36688add73fab2e74fc112c733c5d3c201a6
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2554
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Nemui Trinomius [Tue, 24 Feb 2015 11:37:20 +0000 (20:37 +0900)]
lpc2000: Add LPC407x/8x flash size auto detection
This patch adds auto flash size detection for LPC407x/8x series.
Tested on below listed chips.
LPC4088
LPC1788(regression test)
Change-Id: I82f62678a04eac9b84658bd6d1cfdf45be64c931
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2555
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Jens Bauer <jens@gpio.dk>
Olivier Esver [Wed, 25 Feb 2015 19:29:24 +0000 (20:29 +0100)]
atmega: add support for the at90usb128 flash
Add support for the at90usb128 flash (tested on the RZUSBstick)
Change-Id: Ic042d7c403b20a5cc533da00c30ae6e2139bbd10
Signed-off-by: Olivier Esver <olg.esver@gmail.com>
Reviewed-on: http://openocd.zylin.com/2557
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Mateusz Manowiecki [Mon, 5 Jan 2015 15:40:16 +0000 (16:40 +0100)]
Added system signal handling to Linux version
(with http://www.cons.org/cracauer/sigint.html in mind)
Change-Id: I15f559bc1122a408c3fb9338ba55c16fab3187e1
Signed-off-by: Mateusz Manowiecki <segmentation@fault.pl>
Reviewed-on: http://openocd.zylin.com/2443
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Mateusz Manowiecki [Fri, 23 Jan 2015 20:58:19 +0000 (21:58 +0100)]
jtag/drivers/buspirate: add JTAG_STABLECLOCKS cmd
Solution found on the internet
Change-Id: Ied6f7d9b28131a7ac83b203e4c64d4e9ffec0595
Signed-off-by: Mateusz Manowiecki <segmentation@fault.pl>
Reviewed-on: http://openocd.zylin.com/2496
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Arne Wichmann [Thu, 25 Sep 2014 05:21:24 +0000 (07:21 +0200)]
target & board: AT91SAM7A2 and Olimex SAM7-LA2
Initial Support for AT91SAM7A2 on Olimex SAM7-LA2 board.
The board seems not to be able to reset into halted mode, as srst is
connected to NRESET of the cpu (configured srst_pulls_trst).
JTAG RCLK is connected to CLK.
Tested with interface/ftdi/olimex-arm-usb-ocd-h.cfg.
Change-Id: I2bdd67e3683e45f1119c5850bad294aa107891d8
Signed-off-by: Arne Wichmann <arne.wichmann@gmail.com>
Reviewed-on: http://openocd.zylin.com/2318
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tomas Vanek [Wed, 25 Feb 2015 21:21:58 +0000 (22:21 +0100)]
psoc4 flash driver: cleaned printf PRI... formats
Failed build on Mac OS X 10.10.2 was reported in OpenOCD-devel.
Cleaning types and printf formats. uint32_t prefered for flash/sector sizes.
2 minor changes in comments.
Removed redundant bracket.
Change-Id: Ia06b77af59c2c0ffd10869a4b263a760ca8b0a7a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2558
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Theodore A. Roth [Thu, 29 Jan 2015 00:23:16 +0000 (17:23 -0700)]
nrf51: Update known devices table.
Added new entries to the nrf51_known_devices_table array. New entries
are documented in the "nRF51 Series Compatability Matrix V1.0" found on
the Nordic Semi web site. Reordered entries to match the order found in
the document.
Also added an entry for an undocumented hwid discovered while flashing
the PCA10031 and PCA10028 dev boards.
Change-Id: Icca7da103d437dc28e651f27ab937fe953b9aac9
Signed-off-by: Theodore A. Roth <troth@openavr.org>
Reviewed-on: http://openocd.zylin.com/2514
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
dmitry pervushin [Wed, 4 Feb 2015 10:26:14 +0000 (11:26 +0100)]
flash/nor/spi: add GigaDevice SPI flash
Signed-off-by: dmitry pervushin <dpervushin@gmail.com>
Change-Id: I5a239dc67754ef4be1d9ec36186f434b09aa1e25
Reviewed-on: http://openocd.zylin.com/2530
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Paul Fertser [Fri, 16 Jan 2015 09:17:40 +0000 (12:17 +0300)]
cfg: add board and target configs for TI SimpleLink Wi-Fi CC3200 LaunchPad
Change-Id: I4396ee737c1dad380aa23894bbd1faf75f26d072
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2465
Tested-by: jenkins
Uwe Bonnes [Thu, 11 Dec 2014 15:24:27 +0000 (16:24 +0100)]
Provide genuine F3 nucleo config and source it for STM32F334 Discovery board.
The F334 disco board has a stlink V.2-1 as F3 nucleo boards. Normal F3 disco
boards use stlink v2 and can't ne used.
Change-Id: I77ebef93b184592f25ff18bb2da776d636f60ff0
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2434
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Oleksij Rempel [Mon, 19 Jan 2015 15:43:14 +0000 (16:43 +0100)]
tcl/target|board: add configs for Alphascale asm9260t
This adds configs for Alphascale asm9260t ARM based SoC and
Evaluation Kit based on this chip.
Change-Id: Id8d3a1ef204e3ae84540c2693e3d62650ba82f73
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2515
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Robert P. J. Day [Thu, 9 Jan 2014 16:59:37 +0000 (11:59 -0500)]
Remove long-deprecated "target count" and "target number" commands.
Given that the manual states that these two subcommands are
deprecated and were scheduled to be removed back in 2010,
remove them and the corresponding documentation from the
manual.
Change-Id: Iaac633349d7fcb8b7f964109c7d26dd0cc5fc233
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1860
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Andreas Fritiofson [Wed, 11 Feb 2015 23:12:15 +0000 (00:12 +0100)]
cfg: Fix Kinetis kwikstik/kx config
The flash definition belongs in the target cfg. Add some working area
and suitable reset_config.
Make kx.cfg more similar to klx.cfg.
Disable rclk as it is dead slow and a fixed 1MHz clock seems to work.
Change-Id: I8328f179c3a33be64403da93616abb48651bdfe6
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2227
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Jean-Christian de Rivaz [Thu, 11 Dec 2014 16:50:33 +0000 (17:50 +0100)]
Add SWD protocol support to sysfsgpio
Based on the initial work on bcm2835gpio.c by Paul Fertser with many
additions. Modifications to the GPIO handling was minimal in this
patch. A more big modification is required before cleanup the
interface between bitbang and sysfsgpio.
Change-Id: I54bf2a2aa2ca059368b0e0e105dff6084b73d624
Signed-off-by: Jean-Christian de Rivaz <jc@eclis.ch>
Reviewed-on: http://openocd.zylin.com/2438
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Jean-Christian de Rivaz [Thu, 11 Dec 2014 18:11:49 +0000 (19:11 +0100)]
Add SWD protocol support to bitbang
This is based on the initial work by Paul Fertser with addition of the
switch sequences and new ACK handling. In case of WAIT response, the
sticky bits are cleared and the last operation is repeated. The ACK
handling is based on the interpretation of the 8 February 2006 ARM
Debug Interface v5 Architecture Specification
Change-Id: Id50855b1ffff310177ccf9883dc9eb0d1b4458c8
Signed-off-by: Jean-Christian de Rivaz <jc@eclis.ch>
Reviewed-on: http://openocd.zylin.com/2437
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Matej Kupljen [Wed, 11 Feb 2015 08:28:41 +0000 (09:28 +0100)]
gdb_server: ignore stray + in ACK mode
I couldn't make OpenOCD to work with GDB. I was always getting this in GDB:
(gdb) target remote localhost:3333
Remote debugging using localhost:3333
Ignoring packet error, continuing...
Ignoring packet error, continuing...
Ignoring packet error, continuing...
Ignoring packet error, continuing...
Malformed response to offset query, timeout
(gdb)
While debugging gdb remote protocol, I have seen that gdb responds with:
w ++$?#3f
And those two '+' seems to confuse the OpenOCD parser, if it sees another
'+' sign it emits the DEBUG output and sets the noack_mode to 2. The
problem is that we weren't even IN noack mode, this was set to 0 and then
it explicitly sets it to 2 and thus turning the noack mode on.
Change-Id: If267c9226e57fa83121ded09cf69829f8f0b4b93
Signed-off-by: Matej Kupljen <matej.kupljen@gmail.com>
Reviewed-on: http://openocd.zylin.com/2545
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Uwe Bonnes [Fri, 13 Feb 2015 15:48:23 +0000 (16:48 +0100)]
cortex_m: Add Cortex-M0 identification to ROM-table display.
Change-Id: Id7715a83ba9793844475629aaffd10a81ce586b6
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2549
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Christopher Head [Fri, 7 Nov 2014 22:44:17 +0000 (14:44 -0800)]
Cortex A: fix extra memory read and non-word sizes
Without this patch, to perform a memory read, OpenOCD first issues an
LDC instruction into DBGITR in Stall mode (thus executing the
instruction), then switches to Fast mode and reads from DBGDTRTX once
for each word to transfer.
At the very end of the transfer, the final Fast mode read of DBGDTRTX
has, as always, the side effect of re-issuing the LDC instruction. This
causes two problems:
(1) If the word immediately beyond the end of the requested region is
inaccessible, this spurious LDC will cause a fault. On a fast CPU, the
LDC will finish executing by the time the poll of DSCR takes place,
failing the entire memory read. On a slow CPU, the LDC might finish
executing later, leaving an unexpected and confusing sticky fault lying
around for the next operation to see.
(2) If the LDC succeeds, it will leave the loaded word in DBGDTRTX, thus
setting DBGDSCR.TXFULL=1. The cortex_a_read_apb_ab_memory routine
completes without consuming that last word, thus confusing the next
routine that tries to use DBGDTRTX (this may not have any visible effect
on some implementations, because writing to DBGDTRTXint when TXFULL=1 is
defined as Unpredictable, but I believe it caused a visible problem for
me).
With this patch, the bulk mem_ap_sel_read_buf_noincr is modified to omit
the last word of the block. The second-to-last read of DBGDTRTX by that
function will cause the issue of the LDC for the last word. After
switching back to Normal mode and waiting for that instruction to
finish, do a final read of DBGDTRTX to extract the last word into the
buffer, leaving TXFULL=0.
Without this patch, memory accesses are always expanded such that they
are aligned to the access size. With this patch, accesses are issued
exactly as ordered by the caller. The caller is expected to handle
fragments at the beginning and end of the transfer if the address is
unaligned and an unaligned access is not desired.
Without this patch, the DFAR and DFSR registers, which report the
location and status of data faults, are ignored while performing memory
accesses, which could cause problems debugging an OS page fault handler.
With this patch, DFAR and DFSR are preserved across memory accesses, and
DFSR is decoded in the event of a synchronous fault to provide the
caller with more information about the reason for failure.
Thanks to Boris Brezillon for the original patch whose ideas led to the
non-word access mechanism implemented here and to various code reviewers
for their comments.
Change-Id: I11ae7104fbe69a522efadefc705c9a217a7eef41
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/2381
Tested-by: jenkins
Reviewed-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Paul Fertser [Tue, 27 Jan 2015 17:45:47 +0000 (20:45 +0300)]
doc: stellaris driver supports Tiva C too
Change-Id: I3b77bf0617c0bbba85cfd678adece57aa7d03e32
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2509
Tested-by: jenkins
Paul Fertser [Fri, 23 Jan 2015 20:17:06 +0000 (23:17 +0300)]
flash/nor/stm32lx: add all the IDs and revisions from current RM
RM0038 Rev.12 lists these new parts and introduces the category naming
scheme.
RM0367 Rev.2 (STM32L0x3 RM) doesn't add any new codes.
Change-Id: Id95dd48dda64d5f108dac57d265d29a7db3a1bd1
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2495
Tested-by: jenkins
Paul Fertser [Tue, 27 Jan 2015 18:01:44 +0000 (21:01 +0300)]
README, doc: add mrvlqspi flash driver information
Change-Id: I7a270cdaf3d9119aa75285a8d1e063c2fe2a31b7
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2510
Tested-by: jenkins
Paul Fertser [Tue, 27 Jan 2015 17:25:20 +0000 (20:25 +0300)]
doc, README: mention all the variants supported by lpc2000 driver
Change-Id: I66f9a201426a68fc1314ab7f02b27e36dcab33ba
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2508
Tested-by: jenkins
Andrej Kazmin [Fri, 22 Aug 2014 07:35:06 +0000 (11:35 +0400)]
flash/nor/at91samd: add small delay before checking nvm status
OpenOCD's SWD subsystem doesn't currently have a consistent WAIT
handling (i.e. it doesn't ever retry, just returns an error), so right
after a row write a small delay is needed as AHB access is stalled
during the flashing operation.
The issue was exposed with a samd20 using ftdi SWD transport.
Change-Id: I07d99d3a96845cc689c3904a41f4d41344f200aa
Signed-off-by: Andrej Kazmin <funnyfish@funnyfish.botik.ru>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2268
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Paul Fertser [Fri, 23 Jan 2015 08:38:31 +0000 (11:38 +0300)]
flash/startup: extend "program" command to accept "exit"
This optional argument tells OpenOCD to exit after finishing (either
succesfully, or with an error) the programming sequence. Without it
OpenOCD stays running.
Change-Id: I6ecaf33ff985eea9a9cd02ff644a74403ae3e1e5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2492
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Tue, 27 Jan 2015 18:10:18 +0000 (21:10 +0300)]
server: shutdown command should lead to exit without evaluating the rest
Currently
openocd -c "echo a1; shutdown; echo a2"
outputs both "a1" and "a2" and only then shuts down. This patch fixes
it by making shutdown command throw an exception, so unless it's
caught the shutdown will behave as expected.
Change-Id: I764268b3a9046ff3e9717d04095ea0673f1d755a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2511
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Andreas Fritiofson [Sun, 18 Jan 2015 14:36:52 +0000 (15:36 +0100)]
target/profiling: Use the correct method to access registers
Change-Id: I6b8590dc9d07886b885013b1b767fe2f0739cd6a
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2479
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Andreas Fritiofson [Sun, 18 Jan 2015 14:36:24 +0000 (15:36 +0100)]
xscale: Use the correct method to access registers
Change-Id: I900a0787812cb24d1f74ca50eb6bb4f85375a353
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2478
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Andreas Fritiofson [Sun, 18 Jan 2015 14:35:34 +0000 (15:35 +0100)]
hla_target: Use the correct method to access registers
Change-Id: I853fc5117bdf07ecbc4584ff59d324367b2cb3e3
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2477
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Andreas Fritiofson [Sun, 18 Jan 2015 14:34:42 +0000 (15:34 +0100)]
cortex_m: Use the correct method to access registers
Convert the DWT register store to use a byte array and fix the byte order
bug uncovered by that. Also fix an incorrect access of the PC value.
Change-Id: Idb5acab71bdf5a96895c358324b05c335e4d32ca
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2476
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Andreas Fritiofson [Sun, 18 Jan 2015 14:13:20 +0000 (15:13 +0100)]
nds32: Use the correct method to access registers
The registers are represented as bit arrays intended to be accessed using
the buf_set_* and buf_get_* functions. Storing the register values in
integers enables accessing them directly, which gives different results
depending on host byte order.
Convert the register store to use a byte array instead and fix all the
byte order bugs uncovered by that.
Also merge the 32 and 64 bit register fields. Only one of them is used at
a time and after the change to byte arrays their types are also the same.
Change-Id: I456869a1737f4b4f5e8ecbfc1c63c49a75d21619
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2475
Tested-by: jenkins
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Antony Pavlov [Tue, 25 Feb 2014 20:16:58 +0000 (00:16 +0400)]
mips32: add gdb target description support
This commit is inspired by
commit
1255b18fc650193094666ba8afd2018089cc9794
Author: Spencer Oliver <spen@spen-soft.co.uk>
Date: Fri Sep 13 09:44:36 2013 +0100
armv7m: add gdb target description support
Change-Id: I75c3971fd0599d34ed49fb73975378b57f2a4af0
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
CC: Spencer Oliver <spen@spen-soft.co.uk>
CC: Oleksij Rempel <linux@rempel-privat.de>
CC: Paul Fertser <fercerpav@gmail.com>
CC: Gregory Fong <gregory.0xf0@gmail.com>
Reviewed-on: http://openocd.zylin.com/1972
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Antony Pavlov [Tue, 15 Jul 2014 07:59:04 +0000 (11:59 +0400)]
mips32: use 'unsigned int' for CPU register indices
Change-Id: I77e94b2fe0943a87e1d18d88ebf2a0133aaad728
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2216
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Anton Kuzmin [Mon, 9 Feb 2015 19:23:22 +0000 (22:23 +0300)]
tcl/interface/ftdi: correct LED config for BusBlaster KT-Link
Configure the LED to be off by default, blink on activity.
Change-Id: I8515ee66c49bddf866268b85811be15c2dbc086c
Signed-off-by: Anton Kuzmin <anton.kuzmin@cs.fau.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2539
Tested-by: jenkins
Andreas Bomholtz [Thu, 8 Jan 2015 13:08:26 +0000 (14:08 +0100)]
sim3x: new flash driver for Silabs SiM3 microcontroller family
This is a new driver for Silicon Laboratories SiM3 microcontroller
family, based on the work of Ladislav Bábel. The driver will try to
detect the type of MCU from the device id register, and if this
fails it will use the flash size from the flash bank command.
Driver added to the documentation and to the README.
TCL script added.
Tests:
* Hardware: SiM3C166 (pre-production) and SiM3U167
* Binary: 4kb, 197kb, 256kb
* Flash protect not tested
Change-Id: I701e0cf505ca8ad99be7f83543fe5055b2f65dcc
Signed-off-by: Andreas Bomholtz <andreas@seluxit.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2078
Tested-by: jenkins
Angus Gratton [Fri, 27 Jun 2014 06:13:24 +0000 (16:13 +1000)]
nrf51 - Add async loader. Performance on nrf51822QAA/stlink-v2 from ~3.5KiB/s to ~19.5KiB/s.
Change-Id: Ib0bf41a0cec85f0bd5728551f8ad7f6255e4ea04
Signed-off-by: Angus Gratton <gus@projectgus.com>
[spamjunkeater@gmail.com: Cleanup buffer allocation, detect -1 for unknown pages]
Signed-off-by: Erdem U. Altunyurt <spamjunkeater@gmail.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2204
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Daniel Glöckner [Thu, 20 Nov 2014 22:57:26 +0000 (23:57 +0100)]
armv7a: fix interpretation of MMU table
On armv7 there no longer are 1kB pages. Instead the bit that in
older architectures distinguished 1kB pages from 4kB pages is on
armv7 used for as execute-never marker. There may now also be 16MB
supersections with 40 bit physical address.
Change-Id: I959bdb8012782a9d07d968907a21f50e3d9b356a
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Reviewed-on: http://openocd.zylin.com/2386
Tested-by: jenkins
Reviewed-by: Vladimir Svoboda <ze.vlad@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Joerg Fischer [Sat, 31 Jan 2015 12:00:12 +0000 (13:00 +0100)]
J-Link serial number config option
Add serial option to jlink config commands, handy when there is more than one
adapter connected.
To select adapter
0123456 for OpenOCD, use
jlink serial
0123456
Change-Id: Ib29ce3f0c4975e1169211721a4531bf4db61f1ee
Signed-off-by: Joerg Fischer <turboj@gmx.de>
Reviewed-on: http://openocd.zylin.com/2521
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Olivier Schonken [Tue, 20 Jan 2015 12:17:20 +0000 (14:17 +0200)]
cortex_a: Add Cortex-A5 identification
Add Cortex-A5 identification to ROM-table display, and also
to cortex_a_init_debug_access. This change is mostly cosmetic.
Change-Id: I7b1dd8755d70d45eb5f315aa1918d44a813b3cdf
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/2483
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Paul Fertser [Tue, 27 Jan 2015 19:43:11 +0000 (22:43 +0300)]
README: mention "transport select" in quickstart section
Change-Id: I027635c3c8632efcf58cf979b9cb2f99e9e7f046
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2512
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Sun, 1 Feb 2015 19:19:38 +0000 (22:19 +0300)]
target/image: fix undefined behaviour when loading with GDB
The image struct is malloc'd and hence base_address_set doesn't have a
defined value.
Caught by Valgrind.
Change-Id: Ice15b2299fc768e44e8034eeb93e035076eacd03
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2524
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Tue, 3 Feb 2015 21:49:42 +0000 (00:49 +0300)]
doc: document the OCL (on chip flash loader) driver
Change-Id: I8afe870c7a16b04473f4822c2df9a7607f0480e7
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2529
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Oleksij Rempel [Fri, 30 Jan 2015 20:40:49 +0000 (21:40 +0100)]
tcl: add TP-LINK TL-MR3020 to the firmware recovery script
This adds the board to the list of supported devices for the easy
recovery procedure. Only ram_boot is supported for this target.
Change-Id: I144e1836f8b6257e96a42c98c2668da74ce243f6
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2520
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Oleksij Rempel [Fri, 30 Jan 2015 12:05:31 +0000 (13:05 +0100)]
tcl/target|board: add config Atheros ar9331
Add configs for Atheros ar9331 MIPS based WiSoC and
board based on this chip: TP-LINK TL-MR3020
Change-Id: I9e99719bce4bbb28311f6e9cddb32288db6e7b91
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2519
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Jose de Sousa [Wed, 11 Jun 2014 23:05:20 +0000 (00:05 +0100)]
target: write gmon.out according to target endianness
After profiling gmon.out was being written in little endian format only
which would cause gprof to issue and error and exit on big endian targets.
Change-Id: I526a40adae0f9a439fc5b77cef30fda228198b48
Signed-off-by: Jose de Sousa <jose.t.de.sousa@gmail.com>
Reviewed-on: http://openocd.zylin.com/2168
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Pawel Si [Sat, 6 Dec 2014 16:31:18 +0000 (17:31 +0100)]
mini51: support for Nuvoton NuMicro M051 series flash memory
adds flash support for Nuvoton M052, M054, M058, M0516 microcontrollers
into the mini51 driver, patch also adds support for programing LDROM,
flash data and flash config.
I've tested it on a M0516LBN microcontroller using an ST-LINK/V2:
1. removing security lock:
openocd -f interface/stlink-v2.cfg -f target/m051.cfg -c "init ; halt ; mini51 chip_erase; exit"
2. flashing:
openocd -f interface/stlink-v2.cfg -f target/m051.cfg -c "program file.hex"
Change-Id: I918bfbb42461279c216fb9c22272d77501a2f202
Signed-off-by: Pawel Si <stawel+openocd@gmail.com>
Reviewed-on: http://openocd.zylin.com/2426
Tested-by: jenkins
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Jacob Palsson [Tue, 29 Jul 2014 12:36:40 +0000 (14:36 +0200)]
tcl/target: add CC2538 and CC26xx target files (with cJTAG procedure)
Added support for the Cortex-M3 based TI low power RF SoC CC2538 and
the CC26xx family.
These chips need a start sequence for switching from cJTAG to JTAG
before being used with OpenOCD, this is done in the tcl proc
ti_cjtag_to_4pin_jtag in the ti-cjtag.cfg config.
The configs for CC2538 and CC26xx run the start sequence on post-reset
event and set the ICEPick IDCODE in the data register for OpenOCD to
read, this is done so that every time OpenOCD resets the device, it
will enable JTAG.
Change-Id: I7db620211c0e7e03fad59d24fe31d23a9cdcfedc
Signed-off-by: Jacob Palsson <jaaacke@gmail.com>
Reviewed-on: http://openocd.zylin.com/2232
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Ed Beroset [Sat, 17 Jan 2015 22:04:10 +0000 (17:04 -0500)]
em357: added target files for em357 and em358
This patch adds support for Silicon Labs (formerly Ember) EM357
and EM358 chips and derivatives.
Change-Id: Ie63aed95a2f4ef1a6b955e301a51b4de1b3a5462
Signed-off-by: Ed Beroset <beroset@ieee.org>
Reviewed-on: http://openocd.zylin.com/2470
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Nemui Trinomius [Fri, 12 Sep 2014 22:44:55 +0000 (07:44 +0900)]
jlink: Added hardware version number for JLink firmware on LPC-Link2
JLink firmware on LPC-Link2 has unique hardware version number(0x12).
Change-Id: I76b6e27c47d236da75c61dd6b83d6a823615968d
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2298
Tested-by: jenkins
Reviewed-by: Anders Oleson <anders@openpuma.org>
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Heinz Schweiger [Sun, 12 Jan 2014 10:25:40 +0000 (11:25 +0100)]
cfg: TI Tiva C dk-tm4c129x Evaluation Kits
New Texas Instruments Tiva C Series Boards
http://www.ti.com/tool/dk-tm4c129x
Change-Id: I44f96982e91786b977b3d29e0f4c7053d584a703
Signed-off-by: Heinz Schweiger <openocd@htl-steyr.ac.at>
Reviewed-on: http://openocd.zylin.com/1867
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Michael Brown [Thu, 15 Jan 2015 15:35:21 +0000 (10:35 -0500)]
lpc2000: add chip IDs for LPC11U6x/LPC11E6x
Change-Id: I53568674951ec8a5db5e191c7b50c60b5a84d0b6
Signed-off-by: Michael Brown <fractalmbrown@gmail.com>
Reviewed-on: http://openocd.zylin.com/2463
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tomas Vanek [Mon, 8 Sep 2014 08:34:10 +0000 (10:34 +0200)]
psoc4: support for Cypress PSoC 41xx/42xx family
New NOR flash driver was derived from stm32lx.
Procedure ocd_process_reset_inner is overriden in psoc4.cfg
to handle reset halt and system ROM peculiarities.
Change-Id: Ib835324412d106ad749e1351a8e18e6be34ca500
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2282
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Jussi Kivilinna [Wed, 17 Dec 2014 10:14:32 +0000 (12:14 +0200)]
stm32lx: do not attempt mass-erase in-place of first bank erase
Commit
832f0a5bfb439 'stm32: add mass erase support for STM32L' added
use of mass-erase in-place of bank-erase. This is triggered if first
bank is requested to be fully erased.
This erroneous action completely fails on STM32L162VEY (has 512 KiB
flash in two 256 KiB banks) and also unintently destroying contents of
EEPROM and second flash bank.
Change-Id: I0f13f7b0346747a09c755d72b5b95775ceff5a6f
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Reviewed-on: http://openocd.zylin.com/2441
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Paul Fertser [Sat, 24 Jan 2015 10:57:58 +0000 (13:57 +0300)]
flash/nor/stm32lx: use 0 base to autodetect second bank location
Change-Id: I3c296b3e276fcd4d92e4180fc0d2133eebfcc240
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2503
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Sat, 24 Jan 2015 10:42:00 +0000 (13:42 +0300)]
doc: add stm32lx mass_erase description
Change-Id: Ibe26f40a105dfabcf336ae12fcdc72f4e87513b6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2502
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Fri, 23 Jan 2015 09:40:58 +0000 (12:40 +0300)]
flash/nor/stm32l: unify waiting for busy flag functions
Change-Id: I5e6daff8232bb4807dd13a1951fbf335529661d4
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2491
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Fri, 23 Jan 2015 09:33:50 +0000 (12:33 +0300)]
flash/nor/stm32l: fix mass erase
Topaz reports on http://sourceforge.net/p/openocd/tickets/87/ that
protection level constants are mixed up. This leads to device ending
up in protection level 1 after mass erase.
Additional work is required to actually put the device in RDP Level 1
and then back to Level 0, as Option bootloader launch is a special
kind of full target reset.
To be able to flash properly after mass_erase a "reset init" is needed
(it's anyway recommended to always perform it before any flash
operation).
Change-Id: I9a838909458039bb0114d3019723bf134fa4d7c9
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2490
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Tue, 20 Jan 2015 17:09:02 +0000 (20:09 +0300)]
configure: define WIN32_LEAN_AND_MEAN early to make it effective
This macro makes windows builds faster and helps with the old "#define
interface struct" issue as the word "interface" is part of libusb-0.1
API. However, defining it in replacements.h is too late, as windows.h
gets included by that time from somewhere else.
This solution is provided by Ray Donnelly from the MSYS2 team.
Change-Id: I376a5fb3d106786515d7e1ba44dbd751e4dcdb1b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2486
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Tue, 20 Jan 2015 15:29:31 +0000 (18:29 +0300)]
Makefile.am: link libusb-1.0 after libusb-0.1 to fix dependencies
Since libusb-0.1 might be provided by libusb-compat, it will depend on
libusb-1.0, so needs to be mentioned before it in the link command
line, this is relevant for static linking.
Thanks go to mingwandroid for spotting it during MSYS2 build.
Change-Id: I15cf0b8f084c351b4f93e75686bd0f843477352b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2485
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Fri, 23 Jan 2015 18:36:50 +0000 (21:36 +0300)]
flash/nor/stm32f2x: add new revisions of STM32F4x parts
Change-Id: I7585ccbe12fe079e960ce9e33d9a143672a6a08c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2493
Tested-by: jenkins
Reviewed-by: Rémi PRUD'HOMME <prudhomme.remi@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Rémi PRUD’HOMME [Tue, 20 Jan 2015 13:23:08 +0000 (14:23 +0100)]
Subject: [PATCH] update src/flash/nor/stm32f2x.c
Add the new STM32F446 mcu with 512 Ko
Tested with a eval board
Change-Id: I0c16ce7d32d249c7634d697815207c20e7f778c4
Signed-off-by: prudhomme.remi@gmail.com
Reviewed-on: http://openocd.zylin.com/2484
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Uwe Bonnes [Thu, 11 Dec 2014 15:29:25 +0000 (16:29 +0100)]
Add more STM32F3 IDs in target/stm32f3.cfg.
Change-Id: I4c4462aa025639c4d20e6fa23c8845a69e60afc5
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2435
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Paul Fertser [Thu, 30 Oct 2014 13:22:40 +0000 (16:22 +0300)]
drivers/stlink: clarify "init mode failed" message
The message as it was didn't let the user know that something was wrong
with the target or wiring.
Change-Id: Ib609c2d31959e77413e61c348d0e31d7269d5c58
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2365
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Jens Bauer <jens@gpio.dk>
Paul Fertser [Thu, 15 Jan 2015 20:48:42 +0000 (23:48 +0300)]
tcl/target: add lpc8xx.cfg
This adds a trivial config for LPC8xx chips based on the already
existing infrastructure in lpc1xxx.cfg.
Change-Id: I7384df1f3c2e3e8ab767319728db5c4f8149480f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2464
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Paul Fertser [Mon, 19 Jan 2015 09:05:04 +0000 (12:05 +0300)]
jtag/drivers: remove useless checks causing build failure with clang 3.5.0
Change-Id: Icafab6ac1e3e79c6da1bc163c30744eee4bde8d3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2482
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Andreas Fritiofson [Sun, 18 Jan 2015 11:08:05 +0000 (12:08 +0100)]
armv4_5: Continue the change from uint32_t to uint8_t[4] for regs
Also remove an unrelated no-op cast.
Change-Id: Ibeb6c72e5b0b0347abb568947a05a179661faf2d
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2473
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Paul Fertser [Sat, 17 Jan 2015 12:15:11 +0000 (15:15 +0300)]
Use (uint8_t *) for buf_(set|get)_u(32|64) instead of (void *)
This helps to uncover incorrect usage when a pointer to uint32_t is
passed to those functions which leads to subtle bugs on BE systems.
The reason is that it's normally assumed that any uint32_t variable
holds its value in host byte order, but using but_set_u32 on it
silently does implicit pointer conversion to (void *) and the
assumption ends up broken without any indication.
Change-Id: I48ffd190583d8aa32ec1fef8f1cdc0b4184e4546
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2467
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Jens Bauer [Fri, 16 Jan 2015 22:57:09 +0000 (23:57 +0100)]
stm32f2x: Fix byte order bug.
Do not use buf_set_u32 on integers; they're not buffers.
If using buf_set_u32 on integers, bytes will be exchanged on Big Endian targets.
In this particular case, FLASH_OPTCR was incorrectly written, causing it to often
contain one of these values: 0x00aaaae1, 0x00aaffef, 0x00ffabe1 or 0x00abffe1.
This write-protected the device before flash-programming, causing this command...
flash write_image erase unlock myfile.elf
... to fail, complaining about write-protection.
Repeating the above command would change the OPTCR register each time.
After applying this patch, the OPTCR remains "unchanged".
Change-Id: I73d510fcc2e81a01973ad5c6e1aa22715ebd2743
Signed-off-by: Jens Bauer <jens@gpio.dk>
Reviewed-on: http://openocd.zylin.com/2466
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Paul Fertser [Fri, 5 Dec 2014 10:18:36 +0000 (13:18 +0300)]
flash/nor/kinetis: pull SRST low during mass erase
Mass erase operation might be impacted by different factors,
apparently the most reliable way is to do it while asserting the chip
reset line.
Change-Id: Id6ab57eaec86e402ffdf4f5c8843e7735640f03e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2424
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Andreas Fritiofson [Fri, 9 Jan 2015 00:10:04 +0000 (01:10 +0100)]
jtag: Rewrite TAP verification/auto-probe logic
Enable auto-creating additional discovered TAPs even if some TAPs are
predefined, avoiding initialization failure when it's not necessary.
Also, drop the arbitrary limit on the number of predefined TAPs. Still,
don't auto-create any if there are more than 20 TAPs already, to stop
a noisy connection from creating unlimited TAPs.
Create auto-probed TAPs with less noise.
Reduce code duplication between verification and auto-probing.
Change-Id: I82a504d92dbcc0060206e71f10c5158256b5f561
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2236
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Linking to existing account procedure
If you already have an account and want to add another login method
you
MUST first sign in with your existing account and
then change URL to read
https://review.openocd.org/login/?link
to get to this page again but this time it'll work for linking. Thank you.
SSH host keys fingerprints
1024 SHA256:YKx8b7u5ZWdcbp7/4AeXNaqElP49m6QrwfXaqQGJAOk gerrit-code-review@openocd.zylin.com (DSA)
384 SHA256:jHIbSQa4REvwCFG4cq5LBlBLxmxSqelQPem/EXIrxjk gerrit-code-review@openocd.org (ECDSA)
521 SHA256:UAOPYkU9Fjtcao0Ul/Rrlnj/OsQvt+pgdYSZ4jOYdgs gerrit-code-review@openocd.org (ECDSA)
256 SHA256:A13M5QlnozFOvTllybRZH6vm7iSt0XLxbA48yfc2yfY gerrit-code-review@openocd.org (ECDSA)
256 SHA256:spYMBqEYoAOtK7yZBrcwE8ZpYt6b68Cfh9yEVetvbXg gerrit-code-review@openocd.org (ED25519)
+--[ED25519 256]--+
|=.. |
|+o.. . |
|*.o . . |
|+B . . . |
|Bo. = o S |
|Oo.+ + = |
|oB=.* = . o |
| =+=.+ + E |
|. .=o . o |
+----[SHA256]-----+
2048 SHA256:0Onrb7/PHjpo6iVZ7xQX2riKN83FJ3KGU0TvI0TaFG4 gerrit-code-review@openocd.zylin.com (RSA)
Code Review / openocd.git / log