From 6090a5b158ad212a54510f061226ca58155b51fe Mon Sep 17 00:00:00 2001 From: Alexandre Torgue Date: Mon, 13 Nov 2017 17:00:58 +0100 Subject: [PATCH 1/1] Add STM32H7 config files Add 2 target files: -stm32h7x.cfg -stm32h7x_dual_bank.cfg Add 2 config files for: -STM32H743zi-nucleo bord -STM32H743i and STM32H753i eval boards. Change-Id: I2aae2c5acff4f3ff8e1bf232fda5a11a87f71703 Signed-off-by: Alexandre TORGUE Reviewed-on: http://openocd.zylin.com/4182 Tested-by: jenkins Reviewed-by: Antonio Borneo --- tcl/board/st_nucleo_h743zi.cfg | 10 ++++ tcl/board/stm32h7x3i_eval.cfg | 13 +++++ tcl/target/stm32h7x.cfg | 93 +++++++++++++++++++++++++++++++ tcl/target/stm32h7x_dual_bank.cfg | 7 +++ 4 files changed, 123 insertions(+) create mode 100644 tcl/board/st_nucleo_h743zi.cfg create mode 100644 tcl/board/stm32h7x3i_eval.cfg create mode 100644 tcl/target/stm32h7x.cfg create mode 100644 tcl/target/stm32h7x_dual_bank.cfg diff --git a/tcl/board/st_nucleo_h743zi.cfg b/tcl/board/st_nucleo_h743zi.cfg new file mode 100644 index 0000000000..baedeb6d44 --- /dev/null +++ b/tcl/board/st_nucleo_h743zi.cfg @@ -0,0 +1,10 @@ +# This is an ST NUCLEO-H743ZI board with single STM32H743ZI chip. +# http://www.st.com/en/evaluation-tools/nucleo-h743zi.html + +source [find interface/stlink-v2-1.cfg] + +transport select hla_swd + +source [find target/stm32h7x_dual_bank.cfg] + +reset_config srst_only diff --git a/tcl/board/stm32h7x3i_eval.cfg b/tcl/board/stm32h7x3i_eval.cfg new file mode 100644 index 0000000000..2949ded322 --- /dev/null +++ b/tcl/board/stm32h7x3i_eval.cfg @@ -0,0 +1,13 @@ +# STM32H7[4|5]3I-EVAL: this is for the H7 eval boards. +# This is an ST EVAL-H743XI board with single STM32H743XI chip. +# http://www.st.com/en/evaluation-tools/stm32h743i-eval.html +# This is an ST EVAL-H753XI board with single STM32H753XI chip. +# http://www.st.com/en/evaluation-tools/stm32h753i-eval.html + +source [find interface/stlink-v2-1.cfg] + +transport select hla_swd + +source [find target/stm32h7x_dual_bank.cfg] + +reset_config srst_only diff --git a/tcl/target/stm32h7x.cfg b/tcl/target/stm32h7x.cfg new file mode 100644 index 0000000000..02dbed4a84 --- /dev/null +++ b/tcl/target/stm32h7x.cfg @@ -0,0 +1,93 @@ +# script for stm32h7x family + +# +# stm32h7 devices support both JTAG and SWD transports. +# +source [find target/swj-dp.tcl] +source [find mem_helper.tcl] + +if { [info exists CHIPNAME] } { + set _CHIPNAME $CHIPNAME +} else { + set _CHIPNAME stm32h7x +} + +set _ENDIAN little + +# Work-area is a space in RAM used for flash programming +# By default use 64kB +if { [info exists WORKAREASIZE] } { + set _WORKAREASIZE $WORKAREASIZE +} else { + set _WORKAREASIZE 0x10000 +} + +#jtag scan chain +if { [info exists CPUTAPID] } { + set _CPUTAPID $CPUTAPID +} else { + if { [using_jtag] } { + set _CPUTAPID 0x6ba00477 + } { + set _CPUTAPID 0x6ba02477 + } +} + +swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID + +if {[using_jtag]} { + swj_newdap $_CHIPNAME bs -irlen 5 +} + +set _TARGETNAME $_CHIPNAME.cpu +target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME + +$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0 + +set _FLASHNAME $_CHIPNAME.flash +flash bank $_FLASHNAME stm32h7x 0x08000000 0 0 0 $_TARGETNAME + +# Clock after reset is HSI at 64 MHz, no need of PLL +adapter_khz 1800 + +adapter_nsrst_delay 100 +if {[using_jtag]} { + jtag_ntrst_delay 100 +} + +# use hardware reset, connect under reset +reset_config srst_only srst_nogate + +if {![using_hla]} { + # if srst is not fitted use SYSRESETREQ to + # perform a soft reset + cortex_m reset_config sysresetreq +} + +$_TARGETNAME configure -event examine-end { + # Enable D3 and D1 DBG clocks + # DBGMCU_CR |= D3DBGCKEN | D1DBGCKEN + mmw 0x5C001004 0x00600000 0 + + # Enable debug during low power modes (uses more power) + # DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP in D3 & D1 Domains + mmw 0x5C001004 0x00000187 0 + + # Stop watchdog counters during halt + # DBGMCU_APB3FZ1 |= WWDG1 + mmw 0x5C001034 0x00000040 0 + # DBGMCU_APB4FZ1 |= WDGLSD1 + mmw 0x5C001054 0x00040000 0 +} + +$_TARGETNAME configure -event trace-config { + # Set TRACECLKEN; TRACE_MODE is set to async; when using sync + # change this value accordingly to configure trace pins + # assignment + mmw 0x5C001004 0x00100000 0 +} + +$_TARGETNAME configure -event reset-init { + # Clock after reset is HSI at 64 MHz, no need of PLL + adapter_khz 4000 +} diff --git a/tcl/target/stm32h7x_dual_bank.cfg b/tcl/target/stm32h7x_dual_bank.cfg new file mode 100644 index 0000000000..7e342f9316 --- /dev/null +++ b/tcl/target/stm32h7x_dual_bank.cfg @@ -0,0 +1,7 @@ +# script for stm32h7x family (dual flash bank) +source [find target/stm32h7x.cfg] + +# STM32H7xxxI 2Mo have a dual bank flash. +# Add the second flash bank. +set _FLASHNAME $_CHIPNAME.flash1 +flash bank $_FLASHNAME stm32h7x 0x08100000 0 0 0 $_TARGETNAME -- 2.30.2