From db4b2c25360d7adadb9198e4c817f0d1d211976d Mon Sep 17 00:00:00 2001 From: Andrey Yurovsky Date: Tue, 30 Sep 2014 13:02:49 -0700 Subject: [PATCH] at91samd: fix protect, add EEPROM and boot commands There were two problems with the _protect() feature: 1. The address written was off by a factor of two because the address register takes 16-bit rather than 8-bit addresses. As a result the wrong sectors were (un)protected with the protect command. This has been fixed. 2. The protection settings issued via the lock or unlock region commands don't persist after reset. Making them persist requires modifying the LOCK bits in the User Row using the infrastructure described below. The Atmel SAMD2x MCUs provide a User Row (the size of which is one page). This contains a few settings that users may wish to modify from the debugger, especially during production. This change adds commands to inspect and set: - EEPROM size, the size in bytes of the emulated EEPROM region of the Flash. - Bootloader size, the size in bytes of the protected "boot" section of the Flash. This is done by a careful read-modify-write of the special User Row page, avoiding erasing when possible and disallowing the changing of documented reserved bits. The Atmel SAMD20 datasheet was used for bit positions and descriptions, size tables, etc. and testing was done on a SAMD20 Xplained Pro board. It's technically possible to store arbitrary user data (ex: serial numbers, MAC addresses, etc) in the remaining portion of the User Row page (that is, beyond the first 64 bits of it). The infrastructure used by the eeprom and bootloader commands can be used to access this as well, and this seems safer than exposing the User Row as a normal Flash sector that openocd understands due to the delicate nature of some of the data stored there. Change-Id: I29ca1bdbdc7884bc0ba0ad18af1b6bab78c7ad38 Signed-off-by: Andrey Yurovsky Reviewed-on: http://openocd.zylin.com/2326 Tested-by: jenkins Reviewed-by: Spencer Oliver --- doc/openocd.texi | 28 ++++ src/flash/nor/at91samd.c | 351 ++++++++++++++++++++++++++++++++++----- 2 files changed, 341 insertions(+), 38 deletions(-) diff --git a/doc/openocd.texi b/doc/openocd.texi index 7cba65dd0c..2db8bdd060 100644 --- a/doc/openocd.texi +++ b/doc/openocd.texi @@ -5045,6 +5045,34 @@ at91samd set-security enable @end example @end deffn +@deffn Command {at91samd eeprom} +Shows or sets the EEPROM emulation size configuration, stored in the User Row +of the Flash. When setting, the EEPROM size must be specified in bytes and it +must be one of the permitted sizes according to the datasheet. Settings are +written immediately but only take effect on MCU reset. EEPROM emulation +requires additional firmware support and the minumum EEPROM size may not be +the same as the minimum that the hardware supports. Set the EEPROM size to 0 +in order to disable this feature. + +@example +at91samd eeprom +at91samd eeprom 1024 +@end example +@end deffn + +@deffn Command {at91samd bootloader} +Shows or sets the bootloader size configuration, stored in the User Row of the +Flash. This is called the BOOTPROT region. When setting, the bootloader size +must be specified in bytes and it must be one of the permitted sizes according +to the datasheet. Settings are written immediately but only take effect on +MCU reset. Setting the bootloader size to 0 disables bootloader protection. + +@example +at91samd bootloader +at91samd bootloader 16384 +@end example +@end deffn + @end deffn @anchor{at91sam3} diff --git a/src/flash/nor/at91samd.c b/src/flash/nor/at91samd.c index 9eec0d0ead..7c877c0ff8 100644 --- a/src/flash/nor/at91samd.c +++ b/src/flash/nor/at91samd.c @@ -23,10 +23,13 @@ #endif #include "imp.h" +#include "helper/binarybuffer.h" #define SAMD_NUM_SECTORS 16 +#define SAMD_PAGE_SIZE_MAX 1024 #define SAMD_FLASH ((uint32_t)0x00000000) /* physical Flash memory */ +#define SAMD_USER_ROW ((uint32_t)0x00804000) /* User Row of Flash */ #define SAMD_PAC1 0x41000000 /* Peripheral Access Control 1 */ #define SAMD_DSU 0x41002000 /* Device Service Unit */ #define SAMD_NVMCTRL 0x41004000 /* Non-volatile memory controller */ @@ -222,9 +225,31 @@ static int samd_protect_check(struct flash_bank *bank) return ERROR_OK; } +static int samd_get_flash_page_info(struct target *target, + uint32_t *sizep, int *nump) +{ + int res; + uint32_t param; + + res = target_read_u32(target, SAMD_NVMCTRL + SAMD_NVMCTRL_PARAM, ¶m); + if (res == ERROR_OK) { + /* The PSZ field (bits 18:16) indicate the page size bytes as 2^(3+n) + * so 0 is 8KB and 7 is 1024KB. */ + if (sizep) + *sizep = (8 << ((param >> 16) & 0x7)); + /* The NVMP field (bits 15:0) indicates the total number of pages */ + if (nump) + *nump = param & 0xFFFF; + } else { + LOG_ERROR("Couldn't read NVM Parameters register"); + } + + return res; +} + static int samd_probe(struct flash_bank *bank) { - uint32_t id, param; + uint32_t id; int res; struct samd_info *chip = (struct samd_info *)bank->driver_priv; const struct samd_part *part; @@ -244,22 +269,16 @@ static int samd_probe(struct flash_bank *bank) return ERROR_FAIL; } - res = target_read_u32(bank->target, - SAMD_NVMCTRL + SAMD_NVMCTRL_PARAM, ¶m); - if (res != ERROR_OK) { - LOG_ERROR("Couldn't read NVM Parameters register"); - return res; - } - bank->size = part->flash_kb * 1024; chip->sector_size = bank->size / SAMD_NUM_SECTORS; - /* The PSZ field (bits 18:16) indicate the page size bytes as 2^(3+n) so - * 0 is 8KB and 7 is 1024KB. */ - chip->page_size = (8 << ((param >> 16) & 0x7)); - /* The NVMP field (bits 15:0) indicates the total number of pages */ - chip->num_pages = param & 0xFFFF; + res = samd_get_flash_page_info(bank->target, &chip->page_size, + &chip->num_pages); + if (res != ERROR_OK) { + LOG_ERROR("Couldn't determine Flash page size"); + return res; + } /* Sanity check: the total flash size in the DSU should match the page size * multiplied by the number of pages. */ @@ -372,18 +391,145 @@ static int samd_issue_nvmctrl_command(struct target *target, uint16_t cmd) return ERROR_OK; } -static int samd_protect(struct flash_bank *bank, int set, int first, int last) +static int samd_erase_row(struct target *target, uint32_t address) { int res; - struct samd_info *chip = (struct samd_info *)bank->driver_priv; + /* Set an address contained in the row to be erased */ + res = target_write_u32(target, + SAMD_NVMCTRL + SAMD_NVMCTRL_ADDR, address >> 1); + + /* Issue the Erase Row command to erase that row. */ + if (res == ERROR_OK) + res = samd_issue_nvmctrl_command(target, + address == SAMD_USER_ROW ? SAMD_NVM_CMD_EAR : SAMD_NVM_CMD_ER); + + if (res != ERROR_OK) { + LOG_ERROR("Failed to erase row containing %08" PRIx32, address); + return ERROR_FAIL; + } + + return ERROR_OK; +} + +static bool is_user_row_reserved_bit(uint8_t bit) +{ + /* See Table 9-3 in the SAMD20 datasheet for more information. */ + switch (bit) { + /* Reserved bits */ + case 3: + case 7: + /* Voltage regulator internal configuration with default value of 0x70, + * may not be changed. */ + case 17 ... 24: + /* 41 is voltage regulator internal configuration and must not be + * changed. 42 through 47 are reserved. */ + case 41 ... 47: + return true; + default: + break; + } + + return false; +} + +/* Modify the contents of the User Row in Flash. These are described in Table + * 9-3 of the SAMD20 datasheet. The User Row itself has a size of one page + * and contains a combination of "fuses" and calibration data in bits 24:17. + * We therefore try not to erase the row's contents unless we absolutely have + * to and we don't permit modifying reserved bits. */ +static int samd_modify_user_row(struct target *target, uint32_t value, + uint8_t startb, uint8_t endb) +{ + int res; + + if (is_user_row_reserved_bit(startb) || is_user_row_reserved_bit(endb)) { + LOG_ERROR("Can't modify bits in the requested range"); + return ERROR_FAIL; + } + + /* Retrieve the MCU's page size, in bytes. This is also the size of the + * entire User Row. */ + uint32_t page_size; + res = samd_get_flash_page_info(target, &page_size, NULL); + if (res != ERROR_OK) { + LOG_ERROR("Couldn't determine Flash page size"); + return res; + } + + /* Make sure the size is sane before we allocate. */ + assert(page_size > 0 && page_size <= SAMD_PAGE_SIZE_MAX); + + /* Make sure we're within the single page that comprises the User Row. */ + if (startb >= (page_size * 8) || endb >= (page_size * 8)) { + LOG_ERROR("Can't modify bits outside the User Row page range"); + return ERROR_FAIL; + } + + uint8_t *buf = malloc(page_size); + if (!buf) + return ERROR_FAIL; + + /* Read the user row (comprising one page) by half-words. */ + res = target_read_memory(target, SAMD_USER_ROW, 2, page_size / 2, buf); + if (res != ERROR_OK) + goto out_user_row; + + /* We will need to erase before writing if the new value needs a '1' in any + * position for which the current value had a '0'. Otherwise we can avoid + * erasing. */ + uint32_t cur = buf_get_u32(buf, startb, endb - startb + 1); + if ((~cur) & value) { + res = samd_erase_row(target, SAMD_USER_ROW); + if (res != ERROR_OK) { + LOG_ERROR("Couldn't erase user row"); + goto out_user_row; + } + } + + /* Modify */ + buf_set_u32(buf, startb, endb - startb + 1, value); + + /* Write the page buffer back out to the target. A Flash write will be + * triggered automatically. */ + res = target_write_memory(target, SAMD_USER_ROW, 4, page_size / 4, buf); + if (res != ERROR_OK) + goto out_user_row; + + if (samd_check_error(target)) { + res = ERROR_FAIL; + goto out_user_row; + } + + /* Success */ res = ERROR_OK; +out_user_row: + free(buf); + + return res; +} + +static int samd_protect(struct flash_bank *bank, int set, int first, int last) +{ + struct samd_info *chip = (struct samd_info *)bank->driver_priv; + + /* We can issue lock/unlock region commands with the target running but + * the settings won't persist unless we're able to modify the LOCK regions + * and that requires the target to be halted. */ + if (bank->target->state != TARGET_HALTED) { + LOG_ERROR("Target not halted"); + return ERROR_TARGET_NOT_HALTED; + } + + int res = ERROR_OK; + for (int s = first; s <= last; s++) { if (set != bank->sectors[s].is_protected) { /* Load an address that is within this sector (we use offset 0) */ - res = target_write_u32(bank->target, SAMD_NVMCTRL + SAMD_NVMCTRL_ADDR, - s * chip->sector_size); + res = target_write_u32(bank->target, + SAMD_NVMCTRL + SAMD_NVMCTRL_ADDR, + ((s * chip->sector_size) >> 1)); if (res != ERROR_OK) goto exit; @@ -394,30 +540,24 @@ static int samd_protect(struct flash_bank *bank, int set, int first, int last) goto exit; } } -exit: - samd_protect_check(bank); - - return res; -} -static int samd_erase_row(struct flash_bank *bank, uint32_t address) -{ - int res; + /* We've now applied our changes, however they will be undone by the next + * reset unless we also apply them to the LOCK bits in the User Page. The + * LOCK bits start at bit 48, correspoding to Sector 0 and end with bit 63, + * corresponding to Sector 15. A '1' means unlocked and a '0' means + * locked. See Table 9-3 in the SAMD20 datasheet for more details. */ - /* Set an address contained in the row to be erased */ - res = target_write_u32(bank->target, - SAMD_NVMCTRL + SAMD_NVMCTRL_ADDR, address >> 1); + res = samd_modify_user_row(bank->target, set ? 0x0000 : 0xFFFF, + 48 + first, 48 + last); + if (res != ERROR_OK) + LOG_WARNING("SAMD: protect settings were not made persistent!"); - /* Issue the Erase Row command to erase that row */ - if (res == ERROR_OK) - res = samd_issue_nvmctrl_command(bank->target, SAMD_NVM_CMD_ER); + res = ERROR_OK; - if (res != ERROR_OK) { - LOG_ERROR("Failed to erase row containing %08" PRIx32, address); - return ERROR_FAIL; - } +exit: + samd_protect_check(bank); - return ERROR_OK; + return res; } static int samd_erase(struct flash_bank *bank, int first, int last) @@ -453,7 +593,7 @@ static int samd_erase(struct flash_bank *bank, int first, int last) if (!bank->sectors[s].is_erased) { /* For each row in that sector */ for (int r = s * rows_in_sector; r < (s + 1) * rows_in_sector; r++) { - res = samd_erase_row(bank, r * chip->page_size * 4); + res = samd_erase_row(bank->target, r * chip->page_size * 4); if (res != ERROR_OK) { LOG_ERROR("SAMD: failed to erase sector %d", s); return res; @@ -500,7 +640,7 @@ static int samd_write_row(struct flash_bank *bank, uint32_t address, } /* Erase the row that we'll be writing to */ - res = samd_erase_row(bank, address); + res = samd_erase_row(bank->target, address); if (res != ERROR_OK) return res; @@ -727,6 +867,121 @@ COMMAND_HANDLER(samd_handle_set_security_command) return res; } +COMMAND_HANDLER(samd_handle_eeprom_command) +{ + int res = ERROR_OK; + struct target *target = get_current_target(CMD_CTX); + + if (target) { + if (target->state != TARGET_HALTED) { + LOG_ERROR("Target not halted"); + return ERROR_TARGET_NOT_HALTED; + } + + if (CMD_ARGC >= 1) { + int val = atoi(CMD_ARGV[0]); + uint32_t code; + + if (val == 0) + code = 7; + else { + /* Try to match size in bytes with corresponding size code */ + for (code = 0; code <= 6; code++) { + if (val == (2 << (13 - code))) + break; + } + + if (code > 6) { + command_print(CMD_CTX, "Invalid EEPROM size. Please see " + "datasheet for a list valid sizes."); + return ERROR_COMMAND_SYNTAX_ERROR; + } + } + + res = samd_modify_user_row(target, code, 4, 6); + } else { + uint16_t val; + res = target_read_u16(target, SAMD_USER_ROW, &val); + if (res == ERROR_OK) { + uint32_t size = ((val >> 4) & 0x7); /* grab size code */ + + if (size == 0x7) + command_print(CMD_CTX, "EEPROM is disabled"); + else { + /* Otherwise, 6 is 256B, 0 is 16KB */ + command_print(CMD_CTX, "EEPROM size is %u bytes", + (2 << (13 - size))); + } + } + } + } + + return res; +} + +COMMAND_HANDLER(samd_handle_bootloader_command) +{ + int res = ERROR_OK; + struct target *target = get_current_target(CMD_CTX); + + if (target) { + if (target->state != TARGET_HALTED) { + LOG_ERROR("Target not halted"); + return ERROR_TARGET_NOT_HALTED; + } + + /* Retrieve the MCU's page size, in bytes. */ + uint32_t page_size; + res = samd_get_flash_page_info(target, &page_size, NULL); + if (res != ERROR_OK) { + LOG_ERROR("Couldn't determine Flash page size"); + return res; + } + + if (CMD_ARGC >= 1) { + int val = atoi(CMD_ARGV[0]); + uint32_t code; + + if (val == 0) + code = 7; + else { + /* Try to match size in bytes with corresponding size code */ + for (code = 0; code <= 6; code++) { + if ((unsigned int)val == (2UL << (8UL - code)) * page_size) + break; + } + + if (code > 6) { + command_print(CMD_CTX, "Invalid bootloader size. Please " + "see datasheet for a list valid sizes."); + return ERROR_COMMAND_SYNTAX_ERROR; + } + + } + + res = samd_modify_user_row(target, code, 0, 2); + } else { + uint16_t val; + res = target_read_u16(target, SAMD_USER_ROW, &val); + if (res == ERROR_OK) { + uint32_t size = (val & 0x7); /* grab size code */ + uint32_t nb; + + if (size == 0x7) + nb = 0; + else + nb = (2 << (8 - size)) * page_size; + + /* There are 4 pages per row */ + command_print(CMD_CTX, "Bootloader size is %u bytes (%u rows)", + nb, nb / (page_size * 4)); + } + } + } + + return res; +} + static const struct command_registration at91samd_exec_command_handlers[] = { { .name = "info", @@ -751,6 +1006,26 @@ static const struct command_registration at91samd_exec_command_handlers[] = { "The only way to undo this is to issue the chip-erase" "command.", }, + { + .name = "eeprom", + .usage = "[size_in_bytes]", + .handler = samd_handle_eeprom_command, + .mode = COMMAND_EXEC, + .help = "Show or set the EEPROM size setting, stored in the User Row." + "Please see Table 20-3 of the SAMD20 datasheet for allowed values." + "Changes are stored immediately but take affect after the MCU is" + "reset.", + }, + { + .name = "bootloader", + .usage = "[size_in_bytes]", + .handler = samd_handle_bootloader_command, + .mode = COMMAND_EXEC, + .help = "Show or set the bootloader size, stored in the User Row." + "Please see Table 20-2 of the SAMD20 datasheet for allowed values." + "Changes are stored immediately but take affect after the MCU is" + "reset.", + }, COMMAND_REGISTRATION_DONE }; -- 2.30.2