From faedb1477292dda20267adbdcf6536da3ec77502 Mon Sep 17 00:00:00 2001 From: Paul Fertser Date: Mon, 30 Dec 2013 22:26:36 +0400 Subject: [PATCH] tcl: add bcm47xx config and Asus RT-N16 board using it This adds the bcm47xx config with the special undocumented trick to put it into standard EJTAG mode from the mystic "LV mode". The RAM setup is not done as it would require considerable efforts without much practical gain. The only issue I noticed so far is that "reset" doesn't actually reset the chip. Unfortunately, it's unclear how to make it work properly with SRST as OpenOCD asserts it in MIPS-specific code so the device will enter LV mode again but the LV tap is already disabled by that time, so it's not possible to send the magic command again. Anyway, this config is more than enough to "recover" any RT-N16 provided the hardware is not damaged. Change-Id: I0894e339763e6d20d1c93341c597382b479d039b Signed-off-by: Paul Fertser Reviewed-on: http://openocd.zylin.com/1849 Tested-by: jenkins Reviewed-by: Spencer Oliver --- tcl/board/asus-rt-n16.cfg | 15 +++++++++++++++ tcl/target/bcm4718.cfg | 5 +++++ tcl/target/bcm47xx.cfg | 21 +++++++++++++++++++++ 3 files changed, 41 insertions(+) create mode 100644 tcl/board/asus-rt-n16.cfg create mode 100644 tcl/target/bcm4718.cfg create mode 100644 tcl/target/bcm47xx.cfg diff --git a/tcl/board/asus-rt-n16.cfg b/tcl/board/asus-rt-n16.cfg new file mode 100644 index 0000000000..78f111d380 --- /dev/null +++ b/tcl/board/asus-rt-n16.cfg @@ -0,0 +1,15 @@ +# +# http://wikidevi.com/wiki/ASUS_RT-N16 +# + +set partition_list { + CFE { Bootloader 0xbc000000 0x00040000 } + firmware { "Kernel+rootfs" 0xbc040000 0x01fa0000 } + nvram { "Config space" 0xbdfe0000 0x00020000 } +} + +source [find target/bcm4718.cfg] + +# External 32MB NOR Flash (Macronix MX29GL256EHTI2I-90Q) +set _FLASHNAME $_CHIPNAME.flash +flash bank $_FLASHNAME cfi 0xbc000000 0x02000000 1 1 $_TARGETNAME x16_as_x8 diff --git a/tcl/target/bcm4718.cfg b/tcl/target/bcm4718.cfg new file mode 100644 index 0000000000..8193914a36 --- /dev/null +++ b/tcl/target/bcm4718.cfg @@ -0,0 +1,5 @@ +set _CHIPNAME bcm4718 +set _LVTAPID 0x1471617f +set _CPUID 0x0008c17f + +source [find target/bcm47xx.cfg] diff --git a/tcl/target/bcm47xx.cfg b/tcl/target/bcm47xx.cfg new file mode 100644 index 0000000000..0132bb8024 --- /dev/null +++ b/tcl/target/bcm47xx.cfg @@ -0,0 +1,21 @@ +echo "Forcing reset_config to none to prevent OpenOCD from pulling SRST after the switch from LV is already performed" +reset_config none + +jtag newtap $_CHIPNAME-lv tap -irlen 32 -ircapture 0x1 -irmask 0x1f -expected-id $_LVTAPID -expected-id $_CPUID +jtag configure $_CHIPNAME-lv.tap -event setup "jtag tapenable $_CHIPNAME.cpu" +jtag configure $_CHIPNAME-lv.tap -event tap-disable {} + +jtag newtap $_CHIPNAME cpu -irlen 5 -ircapture 0x1 -irmask 0x1f -expected-id $_CPUID -disable +jtag configure $_CHIPNAME.cpu -event tap-enable "switch_lv_to_ejtag" + +set _TARGETNAME $_CHIPNAME.cpu +target create $_TARGETNAME mips_m4k -endian little -chain-position $_TARGETNAME + +proc switch_lv_to_ejtag {} { + global _CHIPNAME + poll 0 + irscan $_CHIPNAME-lv.tap 0x143ff3a + drscan $_CHIPNAME-lv.tap 32 1 + jtag tapdisable $_CHIPNAME-lv.tap + poll 1 +} -- 2.30.2