1 /**************************************************************************
2 * Copyright (C) 2012 by Andreas Fritiofson *
3 * andreas.fritiofson@gmail.com *
5 * This program is free software; you can redistribute it and/or modify *
6 * it under the terms of the GNU General Public License as published by *
7 * the Free Software Foundation; either version 2 of the License, or *
8 * (at your option) any later version. *
10 * This program is distributed in the hope that it will be useful, *
11 * but WITHOUT ANY WARRANTY; without even the implied warranty of *
12 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the *
13 * GNU General Public License for more details. *
15 * You should have received a copy of the GNU General Public License *
16 * along with this program; if not, write to the *
17 * Free Software Foundation, Inc., *
18 * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. *
19 ***************************************************************************/
23 * JTAG adapters based on the FT2232 full and high speed USB parts are
24 * popular low cost JTAG debug solutions. Many FT2232 based JTAG adapters
25 * are discrete, but development boards may integrate them as alternatives
26 * to more capable (and expensive) third party JTAG pods.
28 * JTAG uses only one of the two communications channels ("MPSSE engines")
29 * on these devices. Adapters based on FT4232 parts have four ports/channels
30 * (A/B/C/D), instead of just two (A/B).
32 * Especially on development boards integrating one of these chips (as
33 * opposed to discrete pods/dongles), the additional channels can be used
34 * for a variety of purposes, but OpenOCD only uses one channel at a time.
36 * - As a USB-to-serial adapter for the target's console UART ...
37 * which may be able to support ROM boot loaders that load initial
38 * firmware images to flash (or SRAM).
40 * - On systems which support ARM's SWD in addition to JTAG, or instead
41 * of it, that second port can be used for reading SWV/SWO trace data.
43 * - Additional JTAG links, e.g. to a CPLD or * FPGA.
45 * FT2232 based JTAG adapters are "dumb" not "smart", because most JTAG
46 * request/response interactions involve round trips over the USB link.
47 * A "smart" JTAG adapter has intelligence close to the scan chain, so it
48 * can for example poll quickly for a status change (usually taking on the
49 * order of microseconds not milliseconds) before beginning a queued
50 * transaction which require the previous one to have completed.
52 * There are dozens of adapters of this type, differing in details which
53 * this driver needs to understand. Those "layout" details are required
54 * as part of FT2232 driver configuration.
56 * This code uses information contained in the MPSSE specification which was
58 * http://www.ftdichip.com/Documents/AppNotes/AN2232C-01_MPSSE_Cmnd.pdf
59 * Hereafter this is called the "MPSSE Spec".
61 * The datasheet for the ftdichip.com's FT2232D part is here:
62 * http://www.ftdichip.com/Documents/DataSheets/DS_FT2232D.pdf
64 * Also note the issue with code 0x4b (clock data to TMS) noted in
65 * http://developer.intra2net.com/mailarchive/html/libftdi/2009/msg00292.html
66 * which can affect longer JTAG state paths.
73 /* project specific includes */
74 #include <jtag/interface.h>
75 #include <transport/transport.h>
76 #include <helper/time_support.h>
84 /* FTDI access library includes */
87 #define JTAG_MODE (LSB_FIRST | POS_EDGE_IN | NEG_EDGE_OUT)
89 static char *ftdi_device_desc
;
90 static char *ftdi_serial
;
91 static uint8_t ftdi_channel
;
94 /* vid = pid = 0 marks the end of the list */
95 static uint16_t ftdi_vid
[MAX_USB_IDS
+ 1] = { 0 };
96 static uint16_t ftdi_pid
[MAX_USB_IDS
+ 1] = { 0 };
98 static struct mpsse_ctx
*mpsse_ctx
;
109 static struct signal
*signals
;
111 static uint16_t output
;
112 static uint16_t direction
;
114 static struct signal
*find_signal_by_name(const char *name
)
116 for (struct signal
*sig
= signals
; sig
; sig
= sig
->next
) {
117 if (strcmp(name
, sig
->name
) == 0)
123 static struct signal
*create_signal(const char *name
)
125 struct signal
**psig
= &signals
;
127 psig
= &(*psig
)->next
;
129 *psig
= calloc(1, sizeof(**psig
));
131 (*psig
)->name
= strdup(name
);
132 if ((*psig
)->name
== NULL
) {
139 static int ftdi_set_signal(const struct signal
*s
, char value
)
145 if (s
->data_mask
== 0 && s
->oe_mask
== 0) {
146 LOG_ERROR("interface doesn't provide signal '%s'", s
->name
);
151 data
= s
->invert_data
;
155 if (s
->data_mask
== 0) {
156 LOG_ERROR("interface can't drive '%s' high", s
->name
);
159 data
= !s
->invert_data
;
164 if (s
->oe_mask
== 0) {
165 LOG_ERROR("interface can't tri-state '%s'", s
->name
);
168 data
= s
->invert_data
;
172 assert(0 && "invalid signal level specifier");
176 output
= data
? output
| s
->data_mask
: output
& ~s
->data_mask
;
177 if (s
->oe_mask
== s
->data_mask
)
178 direction
= oe
? output
| s
->oe_mask
: output
& ~s
->oe_mask
;
180 output
= oe
? output
| s
->oe_mask
: output
& ~s
->oe_mask
;
182 retval
= mpsse_set_data_bits_low_byte(mpsse_ctx
, output
& 0xff, direction
& 0xff);
183 if (retval
== ERROR_OK
)
184 retval
= mpsse_set_data_bits_high_byte(mpsse_ctx
, output
>> 8, direction
>> 8);
185 if (retval
!= ERROR_OK
) {
186 LOG_ERROR("couldn't initialize FTDI GPIO");
187 return ERROR_JTAG_INIT_FAILED
;
195 * Function move_to_state
196 * moves the TAP controller from the current state to a
197 * \a goal_state through a path given by tap_get_tms_path(). State transition
198 * logging is performed by delegation to clock_tms().
200 * @param goal_state is the destination state for the move.
202 static int move_to_state(tap_state_t goal_state
)
204 tap_state_t start_state
= tap_get_state();
206 /* goal_state is 1/2 of a tuple/pair of states which allow convenient
207 lookup of the required TMS pattern to move to this state from the
211 /* do the 2 lookups */
212 int tms_bits
= tap_get_tms_path(start_state
, goal_state
);
213 int tms_count
= tap_get_tms_path_len(start_state
, goal_state
);
215 DEBUG_JTAG_IO("start=%s goal=%s", tap_state_name(start_state
), tap_state_name(goal_state
));
217 /* Track state transitions step by step */
218 for (int i
= 0; i
< tms_count
; i
++)
219 tap_set_state(tap_state_transition(tap_get_state(), (tms_bits
>> i
) & 1));
221 return mpsse_clock_tms_cs_out(mpsse_ctx
,
222 (uint8_t *)&tms_bits
,
229 static int ftdi_speed(int speed
)
232 retval
= mpsse_set_frequency(mpsse_ctx
, speed
);
235 LOG_ERROR("couldn't set FTDI TCK speed");
242 static int ftdi_speed_div(int speed
, int *khz
)
248 static int ftdi_khz(int khz
, int *jtag_speed
)
250 *jtag_speed
= khz
* 1000;
254 static void ftdi_end_state(tap_state_t state
)
256 if (tap_is_state_stable(state
))
257 tap_set_end_state(state
);
259 LOG_ERROR("BUG: %s is not a stable end state", tap_state_name(state
));
264 static int ftdi_execute_runtest(struct jtag_command
*cmd
)
266 int retval
= ERROR_OK
;
270 DEBUG_JTAG_IO("runtest %i cycles, end in %s",
271 cmd
->cmd
.runtest
->num_cycles
,
272 tap_state_name(cmd
->cmd
.runtest
->end_state
));
274 if (tap_get_state() != TAP_IDLE
)
275 move_to_state(TAP_IDLE
);
277 /* TODO: Reuse ftdi_execute_stableclocks */
278 i
= cmd
->cmd
.runtest
->num_cycles
;
279 while (i
> 0 && retval
== ERROR_OK
) {
280 /* there are no state transitions in this code, so omit state tracking */
281 unsigned this_len
= i
> 7 ? 7 : i
;
282 retval
= mpsse_clock_tms_cs_out(mpsse_ctx
, &zero
, 0, this_len
, false, JTAG_MODE
);
286 ftdi_end_state(cmd
->cmd
.runtest
->end_state
);
288 if (tap_get_state() != tap_get_end_state())
289 move_to_state(tap_get_end_state());
291 DEBUG_JTAG_IO("runtest: %i, end in %s",
292 cmd
->cmd
.runtest
->num_cycles
,
293 tap_state_name(tap_get_end_state()));
297 static int ftdi_execute_statemove(struct jtag_command
*cmd
)
299 int retval
= ERROR_OK
;
301 DEBUG_JTAG_IO("statemove end in %s",
302 tap_state_name(cmd
->cmd
.statemove
->end_state
));
304 ftdi_end_state(cmd
->cmd
.statemove
->end_state
);
306 /* shortest-path move to desired end state */
307 if (tap_get_state() != tap_get_end_state() || tap_get_end_state() == TAP_RESET
)
308 move_to_state(tap_get_end_state());
314 * Clock a bunch of TMS (or SWDIO) transitions, to change the JTAG
315 * (or SWD) state machine. REVISIT: Not the best method, perhaps.
317 static int ftdi_execute_tms(struct jtag_command
*cmd
)
319 DEBUG_JTAG_IO("TMS: %d bits", cmd
->cmd
.tms
->num_bits
);
321 /* TODO: Missing tap state tracking, also missing from ft2232.c! */
322 return mpsse_clock_tms_cs_out(mpsse_ctx
,
325 cmd
->cmd
.tms
->num_bits
,
330 static int ftdi_execute_pathmove(struct jtag_command
*cmd
)
332 int retval
= ERROR_OK
;
334 tap_state_t
*path
= cmd
->cmd
.pathmove
->path
;
335 int num_states
= cmd
->cmd
.pathmove
->num_states
;
337 DEBUG_JTAG_IO("pathmove: %i states, current: %s end: %s", num_states
,
338 tap_state_name(tap_get_state()),
339 tap_state_name(path
[num_states
-1]));
342 unsigned bit_count
= 0;
343 uint8_t tms_byte
= 0;
347 /* this loop verifies that the path is legal and logs each state in the path */
348 while (num_states
-- && retval
== ERROR_OK
) {
350 /* either TMS=0 or TMS=1 must work ... */
351 if (tap_state_transition(tap_get_state(), false)
352 == path
[state_count
])
353 buf_set_u32(&tms_byte
, bit_count
++, 1, 0x0);
354 else if (tap_state_transition(tap_get_state(), true)
355 == path
[state_count
]) {
356 buf_set_u32(&tms_byte
, bit_count
++, 1, 0x1);
358 /* ... or else the caller goofed BADLY */
360 LOG_ERROR("BUG: %s -> %s isn't a valid "
361 "TAP state transition",
362 tap_state_name(tap_get_state()),
363 tap_state_name(path
[state_count
]));
367 tap_set_state(path
[state_count
]);
370 if (bit_count
== 7 || num_states
== 0) {
371 retval
= mpsse_clock_tms_cs_out(mpsse_ctx
,
380 tap_set_end_state(tap_get_state());
385 static int ftdi_execute_scan(struct jtag_command
*cmd
)
387 int retval
= ERROR_OK
;
389 DEBUG_JTAG_IO("%s type:%d", cmd
->cmd
.scan
->ir_scan
? "IRSCAN" : "DRSCAN",
390 jtag_scan_type(cmd
->cmd
.scan
));
392 if (cmd
->cmd
.scan
->ir_scan
) {
393 if (tap_get_state() != TAP_IRSHIFT
)
394 move_to_state(TAP_IRSHIFT
);
396 if (tap_get_state() != TAP_DRSHIFT
)
397 move_to_state(TAP_DRSHIFT
);
400 ftdi_end_state(cmd
->cmd
.scan
->end_state
);
402 struct scan_field
*field
= cmd
->cmd
.scan
->fields
;
403 unsigned scan_size
= 0;
405 for (int i
= 0; i
< cmd
->cmd
.scan
->num_fields
; i
++, field
++) {
406 scan_size
+= field
->num_bits
;
407 DEBUG_JTAG_IO("%s%s field %d/%d %d bits",
408 field
->in_value
? "in" : "",
409 field
->out_value
? "out" : "",
411 cmd
->cmd
.scan
->num_fields
,
414 if (i
== cmd
->cmd
.scan
->num_fields
- 1 && tap_get_state() != tap_get_end_state()) {
415 /* Last field, and we're leaving IRSHIFT/DRSHIFT. Clock last bit during tap
417 mpsse_clock_data(mpsse_ctx
,
424 uint8_t last_bit
= 0;
425 if (field
->out_value
)
426 bit_copy(&last_bit
, 0, field
->out_value
, field
->num_bits
- 1, 1);
427 uint8_t tms_bits
= 0x01;
428 retval
= mpsse_clock_tms_cs(mpsse_ctx
,
436 tap_set_state(tap_state_transition(tap_get_state(), 1));
437 retval
= mpsse_clock_tms_cs_out(mpsse_ctx
,
443 tap_set_state(tap_state_transition(tap_get_state(), 0));
445 mpsse_clock_data(mpsse_ctx
,
452 if (retval
!= ERROR_OK
) {
453 LOG_ERROR("failed to add field %d in scan", i
);
458 if (tap_get_state() != tap_get_end_state())
459 move_to_state(tap_get_end_state());
461 DEBUG_JTAG_IO("%s scan, %i bits, end in %s",
462 (cmd
->cmd
.scan
->ir_scan
) ? "IR" : "DR", scan_size
,
463 tap_state_name(tap_get_end_state()));
468 static int ftdi_execute_reset(struct jtag_command
*cmd
)
470 DEBUG_JTAG_IO("reset trst: %i srst %i",
471 cmd
->cmd
.reset
->trst
, cmd
->cmd
.reset
->srst
);
473 if (cmd
->cmd
.reset
->trst
== 1
474 || (cmd
->cmd
.reset
->srst
475 && (jtag_get_reset_config() & RESET_SRST_PULLS_TRST
)))
476 tap_set_state(TAP_RESET
);
478 struct signal
*trst
= find_signal_by_name("nTRST");
479 if (trst
&& cmd
->cmd
.reset
->trst
== 1) {
480 ftdi_set_signal(trst
, '0');
481 } else if (trst
&& cmd
->cmd
.reset
->trst
== 0) {
482 if (jtag_get_reset_config() & RESET_TRST_OPEN_DRAIN
)
483 ftdi_set_signal(trst
, 'z');
485 ftdi_set_signal(trst
, '1');
488 struct signal
*srst
= find_signal_by_name("nSRST");
489 if (srst
&& cmd
->cmd
.reset
->srst
== 1) {
490 ftdi_set_signal(srst
, '0');
491 } else if (srst
&& cmd
->cmd
.reset
->srst
== 0) {
492 if (jtag_get_reset_config() & RESET_SRST_PUSH_PULL
)
493 ftdi_set_signal(srst
, '1');
495 ftdi_set_signal(srst
, 'z');
498 DEBUG_JTAG_IO("trst: %i, srst: %i",
499 cmd
->cmd
.reset
->trst
, cmd
->cmd
.reset
->srst
);
503 static int ftdi_execute_sleep(struct jtag_command
*cmd
)
505 int retval
= ERROR_OK
;
507 DEBUG_JTAG_IO("sleep %" PRIi32
, cmd
->cmd
.sleep
->us
);
509 retval
= mpsse_flush(mpsse_ctx
);
510 jtag_sleep(cmd
->cmd
.sleep
->us
);
511 DEBUG_JTAG_IO("sleep %" PRIi32
" usec while in %s",
513 tap_state_name(tap_get_state()));
517 static int ftdi_execute_stableclocks(struct jtag_command
*cmd
)
519 int retval
= ERROR_OK
;
521 /* this is only allowed while in a stable state. A check for a stable
522 * state was done in jtag_add_clocks()
524 int num_cycles
= cmd
->cmd
.stableclocks
->num_cycles
;
526 /* 7 bits of either ones or zeros. */
527 uint8_t tms
= tap_get_state() == TAP_RESET
? 0x7f : 0x00;
529 /* TODO: Use mpsse_clock_data with in=out=0 for this, if TMS can be set to
530 * the correct level and remain there during the scan */
531 while (num_cycles
> 0 && retval
== ERROR_OK
) {
532 /* there are no state transitions in this code, so omit state tracking */
533 unsigned this_len
= num_cycles
> 7 ? 7 : num_cycles
;
534 retval
= mpsse_clock_tms_cs_out(mpsse_ctx
, &tms
, 0, this_len
, false, JTAG_MODE
);
535 num_cycles
-= this_len
;
538 DEBUG_JTAG_IO("clocks %i while in %s",
539 cmd
->cmd
.stableclocks
->num_cycles
,
540 tap_state_name(tap_get_state()));
544 static int ftdi_execute_command(struct jtag_command
*cmd
)
550 retval
= ftdi_execute_reset(cmd
);
553 retval
= ftdi_execute_runtest(cmd
);
556 retval
= ftdi_execute_statemove(cmd
);
559 retval
= ftdi_execute_pathmove(cmd
);
562 retval
= ftdi_execute_scan(cmd
);
565 retval
= ftdi_execute_sleep(cmd
);
567 case JTAG_STABLECLOCKS
:
568 retval
= ftdi_execute_stableclocks(cmd
);
571 retval
= ftdi_execute_tms(cmd
);
574 LOG_ERROR("BUG: unknown JTAG command type encountered: %d", cmd
->type
);
575 retval
= ERROR_JTAG_QUEUE_FAILED
;
581 static int ftdi_execute_queue(void)
583 int retval
= ERROR_OK
;
585 /* blink, if the current layout has that feature */
586 struct signal
*led
= find_signal_by_name("LED");
588 ftdi_set_signal(led
, '1');
590 for (struct jtag_command
*cmd
= jtag_command_queue
; cmd
; cmd
= cmd
->next
) {
591 /* fill the write buffer with the desired command */
592 if (ftdi_execute_command(cmd
) != ERROR_OK
)
593 retval
= ERROR_JTAG_QUEUE_FAILED
;
597 ftdi_set_signal(led
, '0');
599 retval
= mpsse_flush(mpsse_ctx
);
600 if (retval
!= ERROR_OK
)
601 LOG_ERROR("error while flushing MPSSE queue: %d", retval
);
606 static int ftdi_initialize(void)
610 if (tap_get_tms_path_len(TAP_IRPAUSE
, TAP_IRPAUSE
) == 7)
611 LOG_DEBUG("ftdi interface using 7 step jtag state transitions");
613 LOG_DEBUG("ftdi interface using shortest path jtag state transitions");
615 for (int i
= 0; ftdi_vid
[i
] || ftdi_pid
[i
]; i
++) {
616 mpsse_ctx
= mpsse_open(&ftdi_vid
[i
], &ftdi_pid
[i
], ftdi_device_desc
,
617 ftdi_serial
, ftdi_channel
);
623 return ERROR_JTAG_INIT_FAILED
;
625 retval
= mpsse_set_data_bits_low_byte(mpsse_ctx
, output
& 0xff, direction
& 0xff);
626 if (retval
== ERROR_OK
)
627 retval
= mpsse_set_data_bits_high_byte(mpsse_ctx
, output
>> 8, direction
>> 8);
628 if (retval
!= ERROR_OK
) {
629 LOG_ERROR("couldn't initialize FTDI with 'JTAGkey' layout");
630 return ERROR_JTAG_INIT_FAILED
;
633 retval
= mpsse_loopback_config(mpsse_ctx
, false);
634 if (retval
!= ERROR_OK
) {
635 LOG_ERROR("couldn't write to FTDI to disable loopback");
636 return ERROR_JTAG_INIT_FAILED
;
639 return mpsse_flush(mpsse_ctx
);
642 static int ftdi_quit(void)
644 mpsse_close(mpsse_ctx
);
649 COMMAND_HANDLER(ftdi_handle_device_desc_command
)
652 if (ftdi_device_desc
)
653 free(ftdi_device_desc
);
654 ftdi_device_desc
= strdup(CMD_ARGV
[0]);
656 LOG_ERROR("expected exactly one argument to ftdi_device_desc <description>");
662 COMMAND_HANDLER(ftdi_handle_serial_command
)
667 ftdi_serial
= strdup(CMD_ARGV
[0]);
669 return ERROR_COMMAND_SYNTAX_ERROR
;
675 COMMAND_HANDLER(ftdi_handle_channel_command
)
678 COMMAND_PARSE_NUMBER(u8
, CMD_ARGV
[0], ftdi_channel
);
680 return ERROR_COMMAND_SYNTAX_ERROR
;
685 COMMAND_HANDLER(ftdi_handle_layout_init_command
)
688 return ERROR_COMMAND_SYNTAX_ERROR
;
690 COMMAND_PARSE_NUMBER(u16
, CMD_ARGV
[0], output
);
691 COMMAND_PARSE_NUMBER(u16
, CMD_ARGV
[1], direction
);
696 COMMAND_HANDLER(ftdi_handle_layout_signal_command
)
699 return ERROR_COMMAND_SYNTAX_ERROR
;
701 bool invert_data
= false;
702 uint16_t data_mask
= 0;
703 bool invert_oe
= false;
704 uint16_t oe_mask
= 0;
705 for (unsigned i
= 1; i
< CMD_ARGC
; i
+= 2) {
706 if (strcmp("-data", CMD_ARGV
[i
]) == 0) {
708 COMMAND_PARSE_NUMBER(u16
, CMD_ARGV
[i
+ 1], data_mask
);
709 } else if (strcmp("-ndata", CMD_ARGV
[i
]) == 0) {
711 COMMAND_PARSE_NUMBER(u16
, CMD_ARGV
[i
+ 1], data_mask
);
712 } else if (strcmp("-oe", CMD_ARGV
[i
]) == 0) {
714 COMMAND_PARSE_NUMBER(u16
, CMD_ARGV
[i
+ 1], oe_mask
);
715 } else if (strcmp("-noe", CMD_ARGV
[i
]) == 0) {
717 COMMAND_PARSE_NUMBER(u16
, CMD_ARGV
[i
+ 1], oe_mask
);
719 LOG_ERROR("unknown option '%s'", CMD_ARGV
[i
]);
720 return ERROR_COMMAND_SYNTAX_ERROR
;
725 sig
= find_signal_by_name(CMD_ARGV
[0]);
727 sig
= create_signal(CMD_ARGV
[0]);
729 LOG_ERROR("failed to create signal %s", CMD_ARGV
[0]);
733 sig
->invert_data
= invert_data
;
734 sig
->data_mask
= data_mask
;
735 sig
->invert_oe
= invert_oe
;
736 sig
->oe_mask
= oe_mask
;
741 COMMAND_HANDLER(ftdi_handle_set_signal_command
)
744 return ERROR_COMMAND_SYNTAX_ERROR
;
747 sig
= find_signal_by_name(CMD_ARGV
[0]);
749 LOG_ERROR("interface configuration doesn't define signal '%s'", CMD_ARGV
[0]);
753 switch (*CMD_ARGV
[1]) {
758 /* single character level specifier only */
759 if (CMD_ARGV
[1][1] == '\0') {
760 ftdi_set_signal(sig
, *CMD_ARGV
[1]);
764 LOG_ERROR("unknown signal level '%s', use 0, 1 or z", CMD_ARGV
[1]);
765 return ERROR_COMMAND_SYNTAX_ERROR
;
768 return mpsse_flush(mpsse_ctx
);
771 COMMAND_HANDLER(ftdi_handle_vid_pid_command
)
773 if (CMD_ARGC
> MAX_USB_IDS
* 2) {
774 LOG_WARNING("ignoring extra IDs in ftdi_vid_pid "
775 "(maximum is %d pairs)", MAX_USB_IDS
);
776 CMD_ARGC
= MAX_USB_IDS
* 2;
778 if (CMD_ARGC
< 2 || (CMD_ARGC
& 1)) {
779 LOG_WARNING("incomplete ftdi_vid_pid configuration directive");
781 return ERROR_COMMAND_SYNTAX_ERROR
;
782 /* remove the incomplete trailing id */
787 for (i
= 0; i
< CMD_ARGC
; i
+= 2) {
788 COMMAND_PARSE_NUMBER(u16
, CMD_ARGV
[i
], ftdi_vid
[i
>> 1]);
789 COMMAND_PARSE_NUMBER(u16
, CMD_ARGV
[i
+ 1], ftdi_pid
[i
>> 1]);
793 * Explicitly terminate, in case there are multiples instances of
796 ftdi_vid
[i
>> 1] = ftdi_pid
[i
>> 1] = 0;
801 static const struct command_registration ftdi_command_handlers
[] = {
803 .name
= "ftdi_device_desc",
804 .handler
= &ftdi_handle_device_desc_command
,
805 .mode
= COMMAND_CONFIG
,
806 .help
= "set the USB device description of the FTDI device",
807 .usage
= "description_string",
810 .name
= "ftdi_serial",
811 .handler
= &ftdi_handle_serial_command
,
812 .mode
= COMMAND_CONFIG
,
813 .help
= "set the serial number of the FTDI device",
814 .usage
= "serial_string",
817 .name
= "ftdi_channel",
818 .handler
= &ftdi_handle_channel_command
,
819 .mode
= COMMAND_CONFIG
,
820 .help
= "set the channel of the FTDI device that is used as JTAG",
824 .name
= "ftdi_layout_init",
825 .handler
= &ftdi_handle_layout_init_command
,
826 .mode
= COMMAND_CONFIG
,
827 .help
= "initialize the FTDI GPIO signals used "
828 "to control output-enables and reset signals",
829 .usage
= "data direction",
832 .name
= "ftdi_layout_signal",
833 .handler
= &ftdi_handle_layout_signal_command
,
835 .help
= "define a signal controlled by one or more FTDI GPIO as data "
836 "and/or output enable",
837 .usage
= "name [-data mask|-ndata mask] [-oe mask|-noe mask]",
840 .name
= "ftdi_set_signal",
841 .handler
= &ftdi_handle_set_signal_command
,
842 .mode
= COMMAND_EXEC
,
843 .help
= "control a layout-specific signal",
844 .usage
= "name (1|0|z)",
847 .name
= "ftdi_vid_pid",
848 .handler
= &ftdi_handle_vid_pid_command
,
849 .mode
= COMMAND_CONFIG
,
850 .help
= "the vendor ID and product ID of the FTDI device",
851 .usage
= "(vid pid)* ",
853 COMMAND_REGISTRATION_DONE
856 struct jtag_interface ftdi_interface
= {
858 .supported
= DEBUG_CAP_TMS_SEQ
,
859 .commands
= ftdi_command_handlers
,
860 .transports
= jtag_only
,
862 .init
= ftdi_initialize
,
865 .speed_div
= ftdi_speed_div
,
867 .execute_queue
= ftdi_execute_queue
,
Linking to existing account procedure
If you already have an account and want to add another login method
you
MUST first sign in with your existing account and
then change URL to read
https://review.openocd.org/login/?link
to get to this page again but this time it'll work for linking. Thank you.
SSH host keys fingerprints
1024 SHA256:YKx8b7u5ZWdcbp7/4AeXNaqElP49m6QrwfXaqQGJAOk gerrit-code-review@openocd.zylin.com (DSA)
384 SHA256:jHIbSQa4REvwCFG4cq5LBlBLxmxSqelQPem/EXIrxjk gerrit-code-review@openocd.org (ECDSA)
521 SHA256:UAOPYkU9Fjtcao0Ul/Rrlnj/OsQvt+pgdYSZ4jOYdgs gerrit-code-review@openocd.org (ECDSA)
256 SHA256:A13M5QlnozFOvTllybRZH6vm7iSt0XLxbA48yfc2yfY gerrit-code-review@openocd.org (ECDSA)
256 SHA256:spYMBqEYoAOtK7yZBrcwE8ZpYt6b68Cfh9yEVetvbXg gerrit-code-review@openocd.org (ED25519)
+--[ED25519 256]--+
|=.. |
|+o.. . |
|*.o . . |
|+B . . . |
|Bo. = o S |
|Oo.+ + = |
|oB=.* = . o |
| =+=.+ + E |
|. .=o . o |
+----[SHA256]-----+
2048 SHA256:0Onrb7/PHjpo6iVZ7xQX2riKN83FJ3KGU0TvI0TaFG4 gerrit-code-review@openocd.zylin.com (RSA)