zy1000: fix false positive warning about unitialized local variable

[openocd.git] / src / jtag / zy1000 / zy1000.c

/***************************************************************************
 *   Copyright (C) 2007-2010 by Øyvind Harboe                              *
 *                                                                         *
 *   This program is free software; you can redistribute it and/or modify  *
 *   it under the terms of the GNU General Public License as published by  *
 *   the Free Software Foundation; either version 2 of the License, or     *
 *   (at your option) any later version.                                   *
 *                                                                         *
 *   This program is distributed in the hope that it will be useful,       *
 *   but WITHOUT ANY WARRANTY; without even the implied warranty of        *
 *   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the         *
 *   GNU General Public License for more details.                          *
 *                                                                         *
 *   You should have received a copy of the GNU General Public License     *
 *   along with this program; if not, write to the                         *
 *   Free Software Foundation, Inc.,                                       *
 *   59 Temple Place - Suite 330, Boston, MA  02111-1307, USA.             *
 ***************************************************************************/

/* This file supports the zy1000 debugger: http://www.zylin.com/zy1000.html
 *
 * The zy1000 is a standalone debugger that has a web interface and
 * requires no drivers on the developer host as all communication
 * is via TCP/IP. The zy1000 gets it performance(~400-700kBytes/s
 * DCC downloads @ 16MHz target) as it has an FPGA to hardware
 * accelerate the JTAG commands, while offering *very* low latency
 * between OpenOCD and the FPGA registers.
 *
 * The disadvantage of the zy1000 is that it has a feeble CPU compared to
 * a PC(ca. 50-500 DMIPS depending on how one counts it), whereas a PC
 * is on the order of 10000 DMIPS(i.e. at a factor of 20-200).
 *
 * The zy1000 revc hardware is using an Altera Nios CPU, whereas the
 * revb is using ARM7 + Xilinx.
 *
 * See Zylin web pages or contact Zylin for more information.
 *
 * The reason this code is in OpenOCD rather than OpenOCD linked with the
 * ZY1000 code is that OpenOCD is the long road towards getting
 * libopenocd into place. libopenocd will support both low performance,
 * low latency systems(embedded) and high performance high latency
 * systems(PCs).
 */
#ifdef HAVE_CONFIG_H
#include "config.h"
#endif

#include <target/embeddedice.h>
#include <jtag/minidriver.h>
#include <jtag/interface.h>
#include <time.h>
#include <helper/time_support.h>

#include <netinet/tcp.h>

#if BUILD_ECOSBOARD
#include "zy1000_version.h"

#include <cyg/hal/hal_io.h>             // low level i/o
#include <cyg/hal/hal_diag.h>

#ifdef CYGPKG_HAL_NIOS2
#include <cyg/hal/io.h>
#include <cyg/firmwareutil/firmwareutil.h>
#endif

#define ZYLIN_VERSION GIT_ZY1000_VERSION
#define ZYLIN_DATE __DATE__
#define ZYLIN_TIME __TIME__
#define ZYLIN_OPENOCD GIT_OPENOCD_VERSION
#define ZYLIN_OPENOCD_VERSION "ZY1000 " ZYLIN_VERSION " " ZYLIN_DATE

#endif

static int zy1000_khz(int khz, int *jtag_speed)
{
        if (khz == 0)
        {
                *jtag_speed = 0;
        }
        else
        {
                *jtag_speed = 64000/khz;
        }
        return ERROR_OK;
}

static int zy1000_speed_div(int speed, int *khz)
{
        if (speed == 0)
        {
                *khz = 0;
        }
        else
        {
                *khz = 64000/speed;
        }

        return ERROR_OK;
}

static bool readPowerDropout(void)
{
        uint32_t state;
        // sample and clear power dropout
        ZY1000_POKE(ZY1000_JTAG_BASE + 0x10, 0x80);
        ZY1000_PEEK(ZY1000_JTAG_BASE + 0x10, state);
        bool powerDropout;
        powerDropout = (state & 0x80) != 0;
        return powerDropout;
}


static bool readSRST(void)
{
        uint32_t state;
        // sample and clear SRST sensing
        ZY1000_POKE(ZY1000_JTAG_BASE + 0x10, 0x00000040);
        ZY1000_PEEK(ZY1000_JTAG_BASE + 0x10, state);
        bool srstAsserted;
        srstAsserted = (state & 0x40) != 0;
        return srstAsserted;
}

static int zy1000_srst_asserted(int *srst_asserted)
{
        *srst_asserted = readSRST();
        return ERROR_OK;
}

static int zy1000_power_dropout(int *dropout)
{
        *dropout = readPowerDropout();
        return ERROR_OK;
}

void zy1000_reset(int trst, int srst)
{
        LOG_DEBUG("zy1000 trst=%d, srst=%d", trst, srst);

        /* flush the JTAG FIFO. Not flushing the queue before messing with
         * reset has such interesting bugs as causing hard to reproduce
         * RCLK bugs as RCLK will stop responding when TRST is asserted
         */
        waitIdle();

        if (!srst)
        {
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x14, 0x00000001);
        }
        else
        {
                /* Danger!!! if clk != 0 when in
                 * idle in TAP_IDLE, reset halt on str912 will fail.
                 */
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x10, 0x00000001);
        }

        if (!trst)
        {
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x14, 0x00000002);
        }
        else
        {
                /* assert reset */
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x10, 0x00000002);
        }

        if (trst||(srst && (jtag_get_reset_config() & RESET_SRST_PULLS_TRST)))
        {
                /* we're now in the RESET state until trst is deasserted */
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x20, TAP_RESET);
        } else
        {
                /* We'll get RCLK failure when we assert TRST, so clear any false positives here */
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x14, 0x400);
        }

        /* wait for srst to float back up */
        if ((!srst && ((jtag_get_reset_config() & RESET_TRST_PULLS_SRST) == 0))||
                (!srst && !trst && (jtag_get_reset_config() & RESET_TRST_PULLS_SRST)))
        {
                bool first = true;
                long long start = 0;
                long total = 0;
                for (;;)
                {       
                        // We don't want to sense our own reset, so we clear here.
                        // There is of course a timing hole where we could loose
                        // a "real" reset.
                        if (!readSRST())
                        {
                                if (total > 1)
                                {
                                  LOG_USER("SRST took %dms to deassert", (int)total);
                                }
                                break;
                        }

                        if (first)
                        {
                            first = false;
                            start = timeval_ms();
                        }

                        total = timeval_ms() - start;

                        keep_alive();

                        if (total > 5000)
                        {
                                LOG_ERROR("SRST took too long to deassert: %dms", (int)total);
                            break;
                        }
                }

        }
}

int zy1000_speed(int speed)
{
        /* flush JTAG master FIFO before setting speed */
        waitIdle();

        if (speed == 0)
        {
                /*0 means RCLK*/
                speed = 0;
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x10, 0x100);
                LOG_DEBUG("jtag_speed using RCLK");
        }
        else
        {
                if (speed > 8190 || speed < 2)
                {
                        LOG_USER("valid ZY1000 jtag_speed=[8190,2]. Divisor is 64MHz / even values between 8190-2, i.e. min 7814Hz, max 32MHz");
                        return ERROR_INVALID_ARGUMENTS;
                }

                LOG_USER("jtag_speed %d => JTAG clk=%f", speed, 64.0/(float)speed);
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x14, 0x100);
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x1c, speed&~1);
        }
        return ERROR_OK;
}

static bool savePower;


static void setPower(bool power)
{
        savePower = power;
        if (power)
        {
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x14, 0x8);
        } else
        {
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x10, 0x8);
        }
}

COMMAND_HANDLER(handle_power_command)
{
        switch (CMD_ARGC)
        {
        case 1: {
                bool enable;
                COMMAND_PARSE_ON_OFF(CMD_ARGV[0], enable);
                setPower(enable);
                // fall through
        }
        case 0:
                LOG_INFO("Target power %s", savePower ? "on" : "off");
                break;
        default:
                return ERROR_INVALID_ARGUMENTS;
        }

        return ERROR_OK;
}

#if !BUILD_ECOSBOARD
static char *tcp_server = "notspecified";
static int jim_zy1000_server(Jim_Interp *interp, int argc, Jim_Obj *const *argv)
{
        if (argc != 2)
                return JIM_ERR;

        tcp_server = strdup(Jim_GetString(argv[1], NULL));

        return JIM_OK;
}
#endif

#if BUILD_ECOSBOARD
/* Give TELNET a way to find out what version this is */
static int jim_zy1000_version(Jim_Interp *interp, int argc, Jim_Obj *const *argv)
{
        if ((argc < 1) || (argc > 3))
                return JIM_ERR;
        const char *version_str = NULL;

        if (argc == 1)
        {
                version_str = ZYLIN_OPENOCD_VERSION;
        } else
        {
                const char *str = Jim_GetString(argv[1], NULL);
                const char *str2 = NULL;
                if (argc > 2)
                        str2 = Jim_GetString(argv[2], NULL);
                if (strcmp("openocd", str) == 0)
                {
                        version_str = ZYLIN_OPENOCD;
                }
                else if (strcmp("zy1000", str) == 0)
                {
                        version_str = ZYLIN_VERSION;
                }
                else if (strcmp("date", str) == 0)
                {
                        version_str = ZYLIN_DATE;
                }
                else if (strcmp("time", str) == 0)
                {
                        version_str = ZYLIN_TIME;
                }
                else if (strcmp("pcb", str) == 0)
                {
#ifdef CYGPKG_HAL_NIOS2
                        version_str="c";
#else
                        version_str="b";
#endif
                }
#ifdef CYGPKG_HAL_NIOS2
                else if (strcmp("fpga", str) == 0)
                {

                        /* return a list of 32 bit integers to describe the expected
                         * and actual FPGA
                         */
                        static char *fpga_id = "0x12345678 0x12345678 0x12345678 0x12345678";
                        uint32_t id, timestamp;
                        HAL_READ_UINT32(SYSID_BASE, id);
                        HAL_READ_UINT32(SYSID_BASE+4, timestamp);
                        sprintf(fpga_id, "0x%08x 0x%08x 0x%08x 0x%08x", id, timestamp, SYSID_ID, SYSID_TIMESTAMP);
                        version_str = fpga_id;
                        if ((argc>2) && (strcmp("time", str2) == 0))
                        {
                            time_t last_mod = timestamp;
                            char * t = ctime (&last_mod) ;
                            t[strlen(t)-1] = 0;
                            version_str = t;
                        }
                }
#endif

                else
                {
                        return JIM_ERR;
                }
        }

        Jim_SetResult(interp, Jim_NewStringObj(interp, version_str, -1));

        return JIM_OK;
}
#endif

#ifdef CYGPKG_HAL_NIOS2


struct info_forward
{
        void *data;
        struct cyg_upgrade_info *upgraded_file;
};

static void report_info(void *data, const char * format, va_list args)
{
        char *s = alloc_vprintf(format, args);
        LOG_USER_N("%s", s);
        free(s);
}

struct cyg_upgrade_info firmware_info =
{
                (uint8_t *)0x84000000,
                "/ram/firmware.phi",
                "Firmware",
                0x0300000,
                0x1f00000 -
                0x0300000,
                "ZylinNiosFirmware\n",
                report_info,
};

static int jim_zy1000_writefirmware(Jim_Interp *interp, int argc, Jim_Obj *const *argv)
{
        if (argc != 2)
                return JIM_ERR;

        int length;
        const char *str = Jim_GetString(argv[1], &length);

        /* */
        int tmpFile;
        if ((tmpFile = open(firmware_info.file, O_RDWR | O_CREAT | O_TRUNC)) <= 0)
        {
                return JIM_ERR;
        }
        bool success;
        success = write(tmpFile, str, length) == length;
        close(tmpFile);
        if (!success)
                return JIM_ERR;

        if (!cyg_firmware_upgrade(NULL, firmware_info))
                return JIM_ERR;

        return JIM_OK;
}
#endif

static int
zylinjtag_Jim_Command_powerstatus(Jim_Interp *interp,
                                                                   int argc,
                Jim_Obj * const *argv)
{
        if (argc != 1)
        {
                Jim_WrongNumArgs(interp, 1, argv, "powerstatus");
                return JIM_ERR;
        }

        bool dropout = readPowerDropout();

        Jim_SetResult(interp, Jim_NewIntObj(interp, dropout));

        return JIM_OK;
}



int zy1000_quit(void)
{

        return ERROR_OK;
}



int interface_jtag_execute_queue(void)
{
        uint32_t empty;

        waitIdle();
        ZY1000_PEEK(ZY1000_JTAG_BASE + 0x10, empty);
        /* clear JTAG error register */
        ZY1000_POKE(ZY1000_JTAG_BASE + 0x14, 0x400);

        if ((empty&0x400) != 0)
        {
                LOG_WARNING("RCLK timeout");
                /* the error is informative only as we don't want to break the firmware if there
                 * is a false positive.
                 */
//              return ERROR_FAIL;
        }
        return ERROR_OK;
}





static uint32_t getShiftValue(void)
{
        uint32_t value;
        waitIdle();
        ZY1000_PEEK(ZY1000_JTAG_BASE + 0xc, value);
        VERBOSE(LOG_INFO("getShiftValue %08x", value));
        return value;
}
#if 0
static uint32_t getShiftValueFlip(void)
{
        uint32_t value;
        waitIdle();
        ZY1000_PEEK(ZY1000_JTAG_BASE + 0x18, value);
        VERBOSE(LOG_INFO("getShiftValue %08x (flipped)", value));
        return value;
}
#endif

#if 0
static void shiftValueInnerFlip(const tap_state_t state, const tap_state_t endState, int repeat, uint32_t value)
{
        VERBOSE(LOG_INFO("shiftValueInner %s %s %d %08x (flipped)", tap_state_name(state), tap_state_name(endState), repeat, value));
        uint32_t a,b;
        a = state;
        b = endState;
        ZY1000_POKE(ZY1000_JTAG_BASE + 0xc, value);
        ZY1000_POKE(ZY1000_JTAG_BASE + 0x8, (1 << 15) | (repeat << 8) | (a << 4) | b);
        VERBOSE(getShiftValueFlip());
}
#endif

// here we shuffle N bits out/in
static __inline void scanBits(const uint8_t *out_value, uint8_t *in_value, int num_bits, bool pause, tap_state_t shiftState, tap_state_t end_state)
{
        tap_state_t pause_state = shiftState;
        for (int j = 0; j < num_bits; j += 32)
        {
                int k = num_bits - j;
                if (k > 32)
                {
                        k = 32;
                        /* we have more to shift out */
                } else if (pause)
                {
                        /* this was the last to shift out this time */
                        pause_state = end_state;
                }

                // we have (num_bits + 7)/8 bytes of bits to toggle out.
                // bits are pushed out LSB to MSB
                uint32_t value;
                value = 0;
                if (out_value != NULL)
                {
                        for (int l = 0; l < k; l += 8)
                        {
                                value|=out_value[(j + l)/8]<<l;
                        }
                }
                /* mask away unused bits for easier debugging */
                if (k < 32)
                {
                        value&=~(((uint32_t)0xffffffff) << k);
                } else
                {
                        /* Shifting by >= 32 is not defined by the C standard
                         * and will in fact shift by &0x1f bits on nios */
                }

                shiftValueInner(shiftState, pause_state, k, value);

                if (in_value != NULL)
                {
                        // data in, LSB to MSB
                        value = getShiftValue();
                        // we're shifting in data to MSB, shift data to be aligned for returning the value
                        value >>= 32-k;

                        for (int l = 0; l < k; l += 8)
                        {
                                in_value[(j + l)/8]=(value >> l)&0xff;
                        }
                }
        }
}

static __inline void scanFields(int num_fields, const struct scan_field *fields, tap_state_t shiftState, tap_state_t end_state)
{
        for (int i = 0; i < num_fields; i++)
        {
                scanBits(fields[i].out_value,
                                fields[i].in_value,
                                fields[i].num_bits,
                                (i == num_fields-1),
                                shiftState,
                                end_state);
        }
}

int interface_jtag_add_ir_scan(struct jtag_tap *active, const struct scan_field *fields, tap_state_t state)
{
        int scan_size = 0;
        struct jtag_tap *tap, *nextTap;
        tap_state_t pause_state = TAP_IRSHIFT;

        for (tap = jtag_tap_next_enabled(NULL); tap!= NULL; tap = nextTap)
        {
                nextTap = jtag_tap_next_enabled(tap);
                if (nextTap==NULL)
                {
                        pause_state = state;
                }
                scan_size = tap->ir_length;

                /* search the list */
                if (tap == active)
                {
                        scanFields(1, fields, TAP_IRSHIFT, pause_state);
                        /* update device information */
                        buf_cpy(fields[0].out_value, tap->cur_instr, scan_size);

                        tap->bypass = 0;
                } else
                {
                        /* if a device isn't listed, set it to BYPASS */
                        assert(scan_size <= 32);
                        shiftValueInner(TAP_IRSHIFT, pause_state, scan_size, 0xffffffff);

                        tap->bypass = 1;
                }
        }

        return ERROR_OK;
}





int interface_jtag_add_plain_ir_scan(int num_bits, const uint8_t *out_bits, uint8_t *in_bits, tap_state_t state)
{
        scanBits(out_bits, in_bits, num_bits, true, TAP_IRSHIFT, state);
        return ERROR_OK;
}

int interface_jtag_add_dr_scan(struct jtag_tap *active, int num_fields, const struct scan_field *fields, tap_state_t state)
{
        struct jtag_tap *tap, *nextTap;
        tap_state_t pause_state = TAP_DRSHIFT;
        for (tap = jtag_tap_next_enabled(NULL); tap!= NULL; tap = nextTap)
        {
                nextTap = jtag_tap_next_enabled(tap);
                if (nextTap==NULL)
                {
                        pause_state = state;
                }

                /* Find a range of fields to write to this tap */
                if (tap == active)
                {
                        assert(!tap->bypass);

                        scanFields(num_fields, fields, TAP_DRSHIFT, pause_state);
                } else
                {
                        /* Shift out a 0 for disabled tap's */
                        assert(tap->bypass);
                        shiftValueInner(TAP_DRSHIFT, pause_state, 1, 0);
                }
        }
        return ERROR_OK;
}

int interface_jtag_add_plain_dr_scan(int num_bits, const uint8_t *out_bits, uint8_t *in_bits, tap_state_t state)
{
        scanBits(out_bits, in_bits, num_bits, true, TAP_DRSHIFT, state);
        return ERROR_OK;
}

int interface_jtag_add_tlr()
{
        setCurrentState(TAP_RESET);
        return ERROR_OK;
}


int interface_jtag_add_reset(int req_trst, int req_srst)
{
        zy1000_reset(req_trst, req_srst);
        return ERROR_OK;
}

static int zy1000_jtag_add_clocks(int num_cycles, tap_state_t state, tap_state_t clockstate)
{
        /* num_cycles can be 0 */
        setCurrentState(clockstate);

        /* execute num_cycles, 32 at the time. */
        int i;
        for (i = 0; i < num_cycles; i += 32)
        {
                int num;
                num = 32;
                if (num_cycles-i < num)
                {
                        num = num_cycles-i;
                }
                shiftValueInner(clockstate, clockstate, num, 0);
        }

#if !TEST_MANUAL()
        /* finish in end_state */
        setCurrentState(state);
#else
        tap_state_t t = TAP_IDLE;
        /* test manual drive code on any target */
        int tms;
        uint8_t tms_scan = tap_get_tms_path(t, state);
        int tms_count = tap_get_tms_path_len(tap_get_state(), tap_get_end_state());

        for (i = 0; i < tms_count; i++)
        {
                tms = (tms_scan >> i) & 1;
                waitIdle();
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x28,  tms);
        }
        waitIdle();
        ZY1000_POKE(ZY1000_JTAG_BASE + 0x20, state);
#endif

        return ERROR_OK;
}

int interface_jtag_add_runtest(int num_cycles, tap_state_t state)
{
        return zy1000_jtag_add_clocks(num_cycles, state, TAP_IDLE);
}

int interface_jtag_add_clocks(int num_cycles)
{
        return zy1000_jtag_add_clocks(num_cycles, cmd_queue_cur_state, cmd_queue_cur_state);
}

int interface_add_tms_seq(unsigned num_bits, const uint8_t *seq, enum tap_state state)
{
        /*wait for the fifo to be empty*/
        waitIdle();

        for (unsigned i = 0; i < num_bits; i++)
        {
                int tms;

                if (((seq[i/8] >> (i % 8)) & 1) == 0)
                {
                        tms = 0;
                }
                else
                {
                        tms = 1;
                }

                waitIdle();
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x28, tms);
        }

        waitIdle();
        if (state != TAP_INVALID)
        {
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x20, state);
        } else
        {
                /* this would be normal if we are switching to SWD mode */
        }
        return ERROR_OK;
}

int interface_jtag_add_pathmove(int num_states, const tap_state_t *path)
{
        int state_count;
        int tms = 0;

        state_count = 0;

        tap_state_t cur_state = cmd_queue_cur_state;

        uint8_t seq[16];
        memset(seq, 0, sizeof(seq));
        assert(num_states < (int)((sizeof(seq) * 8)));

        while (num_states)
        {
                if (tap_state_transition(cur_state, false) == path[state_count])
                {
                        tms = 0;
                }
                else if (tap_state_transition(cur_state, true) == path[state_count])
                {
                        tms = 1;
                }
                else
                {
                        LOG_ERROR("BUG: %s -> %s isn't a valid TAP transition", tap_state_name(cur_state), tap_state_name(path[state_count]));
                        exit(-1);
                }

                seq[state_count/8] = seq[state_count/8] | (tms << (state_count % 8));

                cur_state = path[state_count];
                state_count++;
                num_states--;
        }

        return interface_add_tms_seq(state_count, seq, cur_state);
}

static void jtag_pre_post_bits(struct jtag_tap *tap, int *pre, int *post)
{
        /* bypass bits before and after */
        int pre_bits = 0;
        int post_bits = 0;

        bool found = false;
        struct jtag_tap *cur_tap, *nextTap;
        for (cur_tap = jtag_tap_next_enabled(NULL); cur_tap!= NULL; cur_tap = nextTap)
        {
                nextTap = jtag_tap_next_enabled(cur_tap);
                if (cur_tap == tap)
                {
                        found = true;
                } else
                {
                        if (found)
                        {
                                post_bits++;
                        } else
                        {
                                pre_bits++;
                        }
                }
        }
        *pre = pre_bits;
        *post = post_bits;
}

void embeddedice_write_dcc(struct jtag_tap *tap, int reg_addr, uint8_t *buffer, int little, int count)
{

        int pre_bits;
        int post_bits;
        jtag_pre_post_bits(tap, &pre_bits, &post_bits);

        if (pre_bits + post_bits + 6 > 32)
        {
                int i;
                for (i = 0; i < count; i++)
                {
                        embeddedice_write_reg_inner(tap, reg_addr, fast_target_buffer_get_u32(buffer, little));
                        buffer += 4;
                }
        } else
        {
                shiftValueInner(TAP_DRSHIFT, TAP_DRSHIFT, pre_bits, 0);
                int i;
                for (i = 0; i < count - 1; i++)
                {
                        /* Fewer pokes means we get to use the FIFO more efficiently */
                        shiftValueInner(TAP_DRSHIFT, TAP_DRSHIFT, 32, fast_target_buffer_get_u32(buffer, little));
                        shiftValueInner(TAP_DRSHIFT, TAP_IDLE, 6 + post_bits + pre_bits, (reg_addr | (1 << 5)));
                        buffer += 4;
                }
                shiftValueInner(TAP_DRSHIFT, TAP_DRSHIFT, 32, fast_target_buffer_get_u32(buffer, little));
                shiftValueInner(TAP_DRSHIFT, TAP_IDLE, 6 + post_bits, (reg_addr | (1 << 5)));
        }
}



int arm11_run_instr_data_to_core_noack_inner(struct jtag_tap * tap, uint32_t opcode, uint32_t * data, size_t count)
{
#if 0
        int arm11_run_instr_data_to_core_noack_inner_default(struct jtag_tap * tap, uint32_t opcode, uint32_t * data, size_t count);
        return arm11_run_instr_data_to_core_noack_inner_default(tap, opcode, data, count);
#else
        static const int bits[] = {32, 2};
        uint32_t values[] = {0, 0};

        /* FIX!!!!!! the target_write_memory() API started this nasty problem
         * with unaligned uint32_t * pointers... */
        const uint8_t *t = (const uint8_t *)data;


        /* bypass bits before and after */
        int pre_bits;
        int post_bits;
        jtag_pre_post_bits(tap, &pre_bits, &post_bits);

        bool found = false;
        struct jtag_tap *cur_tap, *nextTap;
        for (cur_tap = jtag_tap_next_enabled(NULL); cur_tap!= NULL; cur_tap = nextTap)
        {
                nextTap = jtag_tap_next_enabled(cur_tap);
                if (cur_tap == tap)
                {
                        found = true;
                } else
                {
                        if (found)
                        {
                                post_bits++;
                        } else
                        {
                                pre_bits++;
                        }
                }
        }

        post_bits+=2;


        while (--count > 0)
        {
                shiftValueInner(TAP_DRSHIFT, TAP_DRSHIFT, pre_bits, 0);

                uint32_t value;
                value = *t++;
                value |= (*t++<<8);
                value |= (*t++<<16);
                value |= (*t++<<24);

                shiftValueInner(TAP_DRSHIFT, TAP_DRSHIFT, 32, value);
                /* minimum 2 bits */
                shiftValueInner(TAP_DRSHIFT, TAP_DRPAUSE, post_bits, 0);

#if 1
                /* copy & paste from arm11_dbgtap.c */
                //TAP_DREXIT2, TAP_DRUPDATE, TAP_IDLE, TAP_IDLE, TAP_IDLE, TAP_DRSELECT, TAP_DRCAPTURE, TAP_DRSHIFT

                waitIdle();
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x28, 1);
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x28, 1);
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x28, 0);
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x28, 0);
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x28, 0);
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x28, 1);
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x28, 0);
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x28, 0);
                /* we don't have to wait for the queue to empty here. waitIdle();        */
                ZY1000_POKE(ZY1000_JTAG_BASE + 0x20, TAP_DRSHIFT);
#else
                static const tap_state_t arm11_MOVE_DRPAUSE_IDLE_DRPAUSE_with_delay[] =
                {
                        TAP_DREXIT2, TAP_DRUPDATE, TAP_IDLE, TAP_IDLE, TAP_IDLE, TAP_DRSELECT, TAP_DRCAPTURE, TAP_DRSHIFT
                };

                jtag_add_pathmove(ARRAY_SIZE(arm11_MOVE_DRPAUSE_IDLE_DRPAUSE_with_delay),
                        arm11_MOVE_DRPAUSE_IDLE_DRPAUSE_with_delay);
#endif
        }

        values[0] = *t++;
        values[0] |= (*t++<<8);
        values[0] |= (*t++<<16);
        values[0] |= (*t++<<24);

        /* This will happen on the last iteration updating the current tap state
         * so we don't have to track it during the common code path */
        jtag_add_dr_out(tap,
                2,
                bits,
                values,
                TAP_IDLE);

        return jtag_execute_queue();
#endif
}


static const struct command_registration zy1000_commands[] = {
        {
                .name = "power",
                .handler = handle_power_command,
                .mode = COMMAND_ANY,
                .help = "Turn power switch to target on/off. "
                        "With no arguments, prints status.",
                .usage = "('on'|'off)",
        },
#if BUILD_ECOSBOARD
        {
                .name = "zy1000_version",
                .mode = COMMAND_ANY,
                .jim_handler = jim_zy1000_version,
                .help = "Print version info for zy1000.",
                .usage = "['openocd'|'zy1000'|'date'|'time'|'pcb'|'fpga']",
        },
#else
        {
                .name = "zy1000_server",
                .mode = COMMAND_ANY,
                .jim_handler = jim_zy1000_server,
                .help = "Tcpip address for ZY1000 server.",
                .usage = "address",
        },
#endif
        {
                .name = "powerstatus",
                .mode = COMMAND_ANY,
                .jim_handler = zylinjtag_Jim_Command_powerstatus,
                .help = "Returns power status of target",
        },
#ifdef CYGPKG_HAL_NIOS2
        {
                .name = "updatezy1000firmware",
                .mode = COMMAND_ANY,
                .jim_handler = jim_zy1000_writefirmware,
                .help = "writes firmware to flash",
                /* .usage = "some_string", */
        },
#endif
        COMMAND_REGISTRATION_DONE
};


static int tcp_ip = -1;

/* Write large packets if we can */
static size_t out_pos;
static uint8_t out_buffer[16384];
static size_t in_pos;
static size_t in_write;
static uint8_t in_buffer[16384];

static bool flush_writes(void)
{
        bool ok = (write(tcp_ip, out_buffer, out_pos) == (int)out_pos);
        out_pos = 0;
        return ok;
}

static bool writeLong(uint32_t l)
{
        int i;
        for (i = 0; i < 4; i++)
        {
                uint8_t c = (l >> (i*8))&0xff;
                out_buffer[out_pos++] = c;
                if (out_pos >= sizeof(out_buffer))
                {
                        if (!flush_writes())
                        {
                                return false;
                        }
                }
        }
        return true;
}

static bool readLong(uint32_t *out_data)
{
        if (out_pos > 0)
        {
                if (!flush_writes())
                {
                        return false;
                }
        }

        uint32_t data = 0;
        int i;
        for (i = 0; i < 4; i++)
        {
                uint8_t c;
                if (in_pos == in_write)
                {
                        /* read more */
                        int t;
                        t = read(tcp_ip, in_buffer, sizeof(in_buffer));
                        if (t < 1)
                        {
                                return false;
                        }
                        in_write = (size_t) t;
                        in_pos = 0;
                }
                c = in_buffer[in_pos++];

                data |= (c << (i*8));
        }
        *out_data = data;
        return true;
}

enum ZY1000_CMD
{
        ZY1000_CMD_POKE = 0x0,
        ZY1000_CMD_PEEK = 0x8,
        ZY1000_CMD_SLEEP = 0x1,
};


#if !BUILD_ECOSBOARD

#include <sys/socket.h> /* for socket(), connect(), send(), and recv() */
#include <arpa/inet.h>  /* for sockaddr_in and inet_addr() */

/* We initialize this late since we need to know the server address
 * first.
 */
static void tcpip_open(void)
{
        if (tcp_ip >= 0)
                return;

        struct sockaddr_in echoServAddr; /* Echo server address */

        /* Create a reliable, stream socket using TCP */
        if ((tcp_ip = socket(PF_INET, SOCK_STREAM, IPPROTO_TCP)) < 0)
        {
                fprintf(stderr, "Failed to connect to zy1000 server\n");
                exit(-1);
        }

        /* Construct the server address structure */
        memset(&echoServAddr, 0, sizeof(echoServAddr)); /* Zero out structure */
        echoServAddr.sin_family = AF_INET; /* Internet address family */
        echoServAddr.sin_addr.s_addr = inet_addr(tcp_server); /* Server IP address */
        echoServAddr.sin_port = htons(7777); /* Server port */

        /* Establish the connection to the echo server */
        if (connect(tcp_ip, (struct sockaddr *) &echoServAddr, sizeof(echoServAddr)) < 0)
        {
                fprintf(stderr, "Failed to connect to zy1000 server\n");
                exit(-1);
        }

        int flag = 1;
        setsockopt(tcp_ip,      /* socket affected */
                        IPPROTO_TCP,            /* set option at TCP level */
                        TCP_NODELAY,            /* name of option */
                        (char *)&flag,          /* the cast is historical cruft */
                        sizeof(int));           /* length of option value */

}


/* send a poke */
void zy1000_tcpout(uint32_t address, uint32_t data)
{
        tcpip_open();
        if (!writeLong((ZY1000_CMD_POKE << 24) | address)||
                        !writeLong(data))
        {
                fprintf(stderr, "Could not write to zy1000 server\n");
                exit(-1);
        }
}

uint32_t zy1000_tcpin(uint32_t address)
{
        tcpip_open();
        uint32_t data;
        if (!writeLong((ZY1000_CMD_PEEK << 24) | address)||
                        !readLong(&data))
        {
                fprintf(stderr, "Could not read from zy1000 server\n");
                exit(-1);
        }
        return data;
}

int interface_jtag_add_sleep(uint32_t us)
{
        tcpip_open();
        if (!writeLong((ZY1000_CMD_SLEEP << 24))||
                        !writeLong(us))
        {
                fprintf(stderr, "Could not read from zy1000 server\n");
                exit(-1);
        }
        return ERROR_OK;
}


#endif

#if BUILD_ECOSBOARD
static char tcpip_stack[2048];

static cyg_thread tcpip_thread_object;
static cyg_handle_t tcpip_thread_handle;

/* Infinite loop peeking & poking */
static void tcpipserver(void)
{
        for (;;)
        {
                uint32_t address;
                if (!readLong(&address))
                        return;
                enum ZY1000_CMD c = (address >> 24) & 0xff;
                address &= 0xffffff;
                switch (c)
                {
                        case ZY1000_CMD_POKE:
                        {
                                uint32_t data;
                                if (!readLong(&data))
                                        return;
                                address &= ~0x80000000;
                                ZY1000_POKE(address + ZY1000_JTAG_BASE, data);
                                break;
                        }
                        case ZY1000_CMD_PEEK:
                        {
                                uint32_t data;
                                ZY1000_PEEK(address + ZY1000_JTAG_BASE, data);
                                if (!writeLong(data))
                                        return;
                                break;
                        }
                        case ZY1000_CMD_SLEEP:
                        {
                                uint32_t data;
                                if (!readLong(&data))
                                        return;
                                jtag_sleep(data);
                                break;
                        }
                        default:
                                return;
                }
        }
}


static void tcpip_server(cyg_addrword_t data)
{
        int so_reuseaddr_option = 1;

        int fd;
        if ((fd = socket(AF_INET, SOCK_STREAM, 0)) == -1)
        {
                LOG_ERROR("error creating socket: %s", strerror(errno));
                exit(-1);
        }

        setsockopt(fd, SOL_SOCKET, SO_REUSEADDR, (void*) &so_reuseaddr_option,
                        sizeof(int));

        struct sockaddr_in sin;
        unsigned int address_size;
        address_size = sizeof(sin);
        memset(&sin, 0, sizeof(sin));
        sin.sin_family = AF_INET;
        sin.sin_addr.s_addr = INADDR_ANY;
        sin.sin_port = htons(7777);

        if (bind(fd, (struct sockaddr *) &sin, sizeof(sin)) == -1)
        {
                LOG_ERROR("couldn't bind to socket: %s", strerror(errno));
                exit(-1);
        }

        if (listen(fd, 1) == -1)
        {
                LOG_ERROR("couldn't listen on socket: %s", strerror(errno));
                exit(-1);
        }


        for (;;)
        {
                tcp_ip = accept(fd, (struct sockaddr *) &sin, &address_size);
                if (tcp_ip < 0)
                {
                        continue;
                }

                int flag = 1;
                setsockopt(tcp_ip,      /* socket affected */
                                IPPROTO_TCP,            /* set option at TCP level */
                                TCP_NODELAY,            /* name of option */
                                (char *)&flag,          /* the cast is historical cruft */
                                sizeof(int));           /* length of option value */

                bool save_poll = jtag_poll_get_enabled();

                /* polling will screw up the "connection" */
                jtag_poll_set_enabled(false);

                tcpipserver();

                jtag_poll_set_enabled(save_poll);

                close(tcp_ip);

        }
        close(fd);

}

int interface_jtag_add_sleep(uint32_t us)
{
        jtag_sleep(us);
        return ERROR_OK;
}

#endif


int zy1000_init(void)
{
#if BUILD_ECOSBOARD
        LOG_USER("%s", ZYLIN_OPENOCD_VERSION);
#endif

        ZY1000_POKE(ZY1000_JTAG_BASE + 0x10, 0x30); // Turn on LED1 & LED2

        setPower(true); // on by default


         /* deassert resets. Important to avoid infinite loop waiting for SRST to deassert */
        zy1000_reset(0, 0);
        zy1000_speed(jtag_get_speed());


#if BUILD_ECOSBOARD
        cyg_thread_create(1, tcpip_server, (cyg_addrword_t) 0, "tcip/ip server",
                        (void *) tcpip_stack, sizeof(tcpip_stack),
                        &tcpip_thread_handle, &tcpip_thread_object);
        cyg_thread_resume(tcpip_thread_handle);
#endif

        return ERROR_OK;
}



struct jtag_interface zy1000_interface =
{
        .name = "ZY1000",
        .supported = DEBUG_CAP_TMS_SEQ,
        .execute_queue = NULL,
        .speed = zy1000_speed,
        .commands = zy1000_commands,
        .init = zy1000_init,
        .quit = zy1000_quit,
        .khz = zy1000_khz,
        .speed_div = zy1000_speed_div,
        .power_dropout = zy1000_power_dropout,
        .srst_asserted = zy1000_srst_asserted,
};