target: add Espressif ESP32-S2 basic support

[openocd.git] / tcl / target / stm32f2x.cfg

diff --git a/tcl/target/stm32f2x.cfg b/tcl/target/stm32f2x.cfg
index a4aded007c576e75c39652b369052f723c26de1a..d790febd56464ede05c66838acb014c1fe285a1c 100644 (file)
--- a/tcl/target/stm32f2x.cfg
+++ b/tcl/target/stm32f2x.cfg
@@ -4,6 +4,7 @@
 # stm32 devices support both JTAG and SWD transports.
 #
 source [find target/swj-dp.tcl]
+source [find mem_helper.tcl]
 
 if { [info exists CHIPNAME] } {
    set _CHIPNAME $CHIPNAME
@@ -11,11 +12,7 @@ if { [info exists CHIPNAME] } {
    set _CHIPNAME stm32f2x
 }
 
-if { [info exists ENDIAN] } {
-   set _ENDIAN $ENDIAN
-} else {
-   set _ENDIAN little
-}
+set _ENDIAN little
 
 # Work-area is a space in RAM used for flash programming
 # By default use 64kB
@@ -31,9 +28,9 @@ if { [info exists WORKAREASIZE] } {
 # bit more to be on the safe side. Perhaps superstition, but if are
 # running off a crystal, we can run closer to the limit. Note
 # that there can be a pretty wide band where things are more or less stable.
-adapter_khz 1000
+adapter speed 1000
 
-adapter_nsrst_delay 100
+adapter srst delay 100
 if {[using_jtag]} {
  jtag_ntrst_delay 100
 }
@@ -52,30 +49,41 @@ if { [info exists CPUTAPID] } {
 }
 
 swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-if { [info exists BSTAPID] } {
-   set _BSTAPID $BSTAPID
-} else {
-  # See STM Document RM0033
-  # Section 32.6.2
-  # 
-  set _BSTAPID 0x06411041
-}
+dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
 
 if {[using_jtag]} {
- swj_newdap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID
+       jtag newtap $_CHIPNAME bs -irlen 5
 }
 
 set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
+target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
 
 $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
 
 set _FLASHNAME $_CHIPNAME.flash
 flash bank $_FLASHNAME stm32f2x 0 0 0 0 $_TARGETNAME
+flash bank $_CHIPNAME.otp stm32f2x 0x1fff7800 0 0 0 $_TARGETNAME
+
+reset_config srst_nogate
 
 if {![using_hla]} {
    # if srst is not fitted use SYSRESETREQ to
    # perform a soft reset
    cortex_m reset_config sysresetreq
 }
+
+$_TARGETNAME configure -event examine-end {
+       # DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
+       mmw 0xE0042004 0x00000007 0
+
+       # Stop watchdog counters during halt
+       # DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
+       mmw 0xE0042008 0x00001800 0
+}
+
+$_TARGETNAME configure -event trace-config {
+       # Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
+       # change this value accordingly to configure trace pins
+       # assignment
+       mmw 0xE0042004 0x00000020 0
+}