Some help text end with a useless space character.
Remove it.
Change-Id: I397e1194fac8042f0fab694222f925f906716de3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6222
Tested-by: jenkins
.handler = adapter_transports_command,
.mode = COMMAND_CONFIG,
.help = "Declare transports the adapter supports.",
.handler = adapter_transports_command,
.mode = COMMAND_CONFIG,
.help = "Declare transports the adapter supports.",
- .usage = "transport ... ",
+ .usage = "transport ...",
.handler = &cmsis_dap_handle_vid_pid_command,
.mode = COMMAND_CONFIG,
.help = "the vendor ID and product ID of the CMSIS-DAP device",
.handler = &cmsis_dap_handle_vid_pid_command,
.mode = COMMAND_CONFIG,
.help = "the vendor ID and product ID of the CMSIS-DAP device",
- .usage = "(vid pid)* ",
},
{
.name = "cmsis_dap_serial",
},
{
.name = "cmsis_dap_serial",
.handler = &ftdi_handle_vid_pid_command,
.mode = COMMAND_CONFIG,
.help = "the vendor ID and product ID of the FTDI device",
.handler = &ftdi_handle_vid_pid_command,
.mode = COMMAND_CONFIG,
.help = "the vendor ID and product ID of the FTDI device",
- .usage = "(vid pid)* ",
},
{
.name = "ftdi_tdo_sample_edge",
},
{
.name = "ftdi_tdo_sample_edge",
.handler = &hl_interface_handle_vid_pid_command,
.mode = COMMAND_CONFIG,
.help = "the vendor and product ID of the adapter",
.handler = &hl_interface_handle_vid_pid_command,
.mode = COMMAND_CONFIG,
.help = "the vendor and product ID of the adapter",
- .usage = "(vid pid)* ",
},
{
.name = "hla_stlink_backend",
},
{
.name = "hla_stlink_backend",
.help = "Create a new TAP instance named basename.tap_type, "
"and appends it to the scan chain.",
.usage = "basename tap_type '-irlen' count "
.help = "Create a new TAP instance named basename.tap_type, "
"and appends it to the scan chain.",
.usage = "basename tap_type '-irlen' count "
- "['-expected_id' number] ",
+ "['-expected_id' number]",
"['-expected_id' number] "
"['-ignore-version'] "
"['-ircapture' number] "
"['-expected_id' number] "
"['-ignore-version'] "
"['-ircapture' number] "
},
{
.name = "tapisenabled",
},
{
.name = "tapisenabled",
.mode = COMMAND_ANY,
.help = "Wait for an SRST deassert. "
"Useful for cases where you need something to happen within ms "
.mode = COMMAND_ANY,
.help = "Wait for an SRST deassert. "
"Useful for cases where you need something to happen within ms "
- "of an srst deassert. Timeout in ms ",
+ "of an srst deassert. Timeout in ms",
.handler = handle_arm_disassemble_command,
.mode = COMMAND_EXEC,
.usage = "address [count ['thumb']]",
.handler = handle_arm_disassemble_command,
.mode = COMMAND_EXEC,
.usage = "address [count ['thumb']]",
- .help = "disassemble instructions ",
+ .help = "disassemble instructions",
.name = "conf",
.handler = armv7a_l2x_cache_conf_cmd,
.mode = COMMAND_ANY,
.name = "conf",
.handler = armv7a_l2x_cache_conf_cmd,
.mode = COMMAND_ANY,
- .help = "configure l2x cache ",
+ .help = "configure l2x cache",
.usage = "<base_addr> <number_of_way>",
},
{
.usage = "<base_addr> <number_of_way>",
},
{
.handler = dsp563xx_remove_watchpoint_command,
.mode = COMMAND_EXEC,
.help = "remove watchpoint custom",
.handler = dsp563xx_remove_watchpoint_command,
.mode = COMMAND_EXEC,
.help = "remove watchpoint custom",
},
COMMAND_REGISTRATION_DONE
};
},
COMMAND_REGISTRATION_DONE
};
.handler = handle_target_reset_nag,
.mode = COMMAND_ANY,
.help = "Nag after each reset about options that could have been "
.handler = handle_target_reset_nag,
.mode = COMMAND_ANY,
.help = "Nag after each reset about options that could have been "
- "enabled to improve performance. ",
+ "enabled to improve performance.",
.usage = "['enable'|'disable']",
},
{
.name = "ps",
.handler = handle_ps_command,
.mode = COMMAND_EXEC,
.usage = "['enable'|'disable']",
},
{
.name = "ps",
.handler = handle_ps_command,
.mode = COMMAND_EXEC,
- .help = "list all tasks ",
- .usage = " ",
+ .help = "list all tasks",
+ .usage = "",
},
{
.name = "test_mem_access",
},
{
.name = "test_mem_access",
Linking to existing account procedure
If you already have an account and want to add another login method
you
MUST first sign in with your existing account and
then change URL to read
https://review.openocd.org/login/?link
to get to this page again but this time it'll work for linking. Thank you.
SSH host keys fingerprints
1024 SHA256:YKx8b7u5ZWdcbp7/4AeXNaqElP49m6QrwfXaqQGJAOk gerrit-code-review@openocd.zylin.com (DSA)
384 SHA256:jHIbSQa4REvwCFG4cq5LBlBLxmxSqelQPem/EXIrxjk gerrit-code-review@openocd.org (ECDSA)
521 SHA256:UAOPYkU9Fjtcao0Ul/Rrlnj/OsQvt+pgdYSZ4jOYdgs gerrit-code-review@openocd.org (ECDSA)
256 SHA256:A13M5QlnozFOvTllybRZH6vm7iSt0XLxbA48yfc2yfY gerrit-code-review@openocd.org (ECDSA)
256 SHA256:spYMBqEYoAOtK7yZBrcwE8ZpYt6b68Cfh9yEVetvbXg gerrit-code-review@openocd.org (ED25519)
+--[ED25519 256]--+
|=.. |
|+o.. . |
|*.o . . |
|+B . . . |
|Bo. = o S |
|Oo.+ + = |
|oB=.* = . o |
| =+=.+ + E |
|. .=o . o |
+----[SHA256]-----+
2048 SHA256:0Onrb7/PHjpo6iVZ7xQX2riKN83FJ3KGU0TvI0TaFG4 gerrit-code-review@openocd.zylin.com (RSA)