#include <helper/align.h>
#include <helper/binarybuffer.h>
#include <target/algorithm.h>
-#include <target/armv7m.h>
+#include <target/cortex_m.h>
#include "bits.h"
#include "stm32l4x.h"
*
* RM0461 (STM32WLEx)
* http://www.st.com/resource/en/reference_manual/dm00530369.pdf
+ *
+ * RM0453 (STM32WL5x)
+ * http://www.st.com/resource/en/reference_manual/dm00451556.pdf
*/
/* STM32G0xxx series for reference.
STM32_FLASH_OPTKEYR_INDEX,
STM32_FLASH_SR_INDEX,
STM32_FLASH_CR_INDEX,
+ /* for some devices like STM32WL5x, the CPU2 have a dedicated C2CR register w/o LOCKs,
+ * so it uses the C2CR for flash operations and CR for checking locks and locking */
+ STM32_FLASH_CR_WLK_INDEX, /* FLASH_CR_WITH_LOCK */
STM32_FLASH_OPTR_INDEX,
STM32_FLASH_WRP1AR_INDEX,
STM32_FLASH_WRP1BR_INDEX,
[STM32_FLASH_WRP2BR_INDEX] = 0x050,
};
+static const uint32_t stm32wl_cpu2_flash_regs[STM32_FLASH_REG_INDEX_NUM] = {
+ [STM32_FLASH_ACR_INDEX] = 0x000,
+ [STM32_FLASH_KEYR_INDEX] = 0x008,
+ [STM32_FLASH_OPTKEYR_INDEX] = 0x010,
+ [STM32_FLASH_SR_INDEX] = 0x060,
+ [STM32_FLASH_CR_INDEX] = 0x064,
+ [STM32_FLASH_CR_WLK_INDEX] = 0x014,
+ [STM32_FLASH_OPTR_INDEX] = 0x020,
+ [STM32_FLASH_WRP1AR_INDEX] = 0x02C,
+ [STM32_FLASH_WRP1BR_INDEX] = 0x030,
+};
+
static const uint32_t stm32l5_ns_flash_regs[STM32_FLASH_REG_INDEX_NUM] = {
[STM32_FLASH_ACR_INDEX] = 0x000,
[STM32_FLASH_KEYR_INDEX] = 0x008, /* NSKEYR */
.id = 0x497,
.revs = stm32_497_revs,
.num_revs = ARRAY_SIZE(stm32_497_revs),
- .device_str = "STM32WLEx",
+ .device_str = "STM32WLEx/WL5x",
.max_flash_size_kb = 256,
.flags = F_NONE,
.flash_regs_base = 0x58004000,
return ERROR_OK;
}
+static inline int stm32l4_get_flash_cr_with_lock_index(struct flash_bank *bank)
+{
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+ return (stm32l4_info->flash_regs[STM32_FLASH_CR_WLK_INDEX]) ?
+ STM32_FLASH_CR_WLK_INDEX : STM32_FLASH_CR_INDEX;
+}
+
static int stm32l4_unlock_reg(struct flash_bank *bank)
{
+ const uint32_t flash_cr_index = stm32l4_get_flash_cr_with_lock_index(bank);
uint32_t ctrl;
/* first check if not already unlocked
* otherwise writing on STM32_FLASH_KEYR will fail
*/
- int retval = stm32l4_read_flash_reg_by_index(bank, STM32_FLASH_CR_INDEX, &ctrl);
+ int retval = stm32l4_read_flash_reg_by_index(bank, flash_cr_index, &ctrl);
if (retval != ERROR_OK)
return retval;
if (retval != ERROR_OK)
return retval;
- retval = stm32l4_read_flash_reg_by_index(bank, STM32_FLASH_CR_INDEX, &ctrl);
+ retval = stm32l4_read_flash_reg_by_index(bank, flash_cr_index, &ctrl);
if (retval != ERROR_OK)
return retval;
static int stm32l4_unlock_option_reg(struct flash_bank *bank)
{
+ const uint32_t flash_cr_index = stm32l4_get_flash_cr_with_lock_index(bank);
uint32_t ctrl;
- int retval = stm32l4_read_flash_reg_by_index(bank, STM32_FLASH_CR_INDEX, &ctrl);
+ int retval = stm32l4_read_flash_reg_by_index(bank, flash_cr_index, &ctrl);
if (retval != ERROR_OK)
return retval;
if (retval != ERROR_OK)
return retval;
- retval = stm32l4_read_flash_reg_by_index(bank, STM32_FLASH_CR_INDEX, &ctrl);
+ retval = stm32l4_read_flash_reg_by_index(bank, flash_cr_index, &ctrl);
if (retval != ERROR_OK)
return retval;
stm32l4_info->probed = false;
err_lock:
- retval2 = stm32l4_write_flash_reg_by_index(bank, STM32_FLASH_CR_INDEX, FLASH_LOCK | FLASH_OPTLOCK);
+ retval2 = stm32l4_write_flash_reg_by_index(bank, stm32l4_get_flash_cr_with_lock_index(bank),
+ FLASH_LOCK | FLASH_OPTLOCK);
if (retval != ERROR_OK)
return retval;
retval = stm32l4_wait_status_busy(bank, FLASH_ERASE_TIMEOUT);
err_lock:
- retval2 = stm32l4_write_flash_reg_by_index(bank, STM32_FLASH_CR_INDEX, FLASH_LOCK | FLASH_OPTLOCK);
+ retval2 = stm32l4_write_flash_reg_by_index(bank, stm32l4_get_flash_cr_with_lock_index(bank),
+ FLASH_LOCK | FLASH_OPTLOCK);
stm32l4_info->flash_regs = saved_flash_regs;
if (retval != ERROR_OK)
}
err_lock:
- retval2 = stm32l4_write_flash_reg_by_index(bank, STM32_FLASH_CR_INDEX, FLASH_LOCK);
+ retval2 = stm32l4_write_flash_reg_by_index(bank, stm32l4_get_flash_cr_with_lock_index(bank), FLASH_LOCK);
if (stm32l4_info->tzen && (stm32l4_info->rdp == RDP_LEVEL_0)) {
/* restore all FLASH pages as non-secure */
err_lock:
- retval2 = stm32l4_write_flash_reg_by_index(bank, STM32_FLASH_CR_INDEX, FLASH_LOCK);
+ retval2 = stm32l4_write_flash_reg_by_index(bank, stm32l4_get_flash_cr_with_lock_index(bank), FLASH_LOCK);
if (stm32l4_info->tzen && (stm32l4_info->rdp == RDP_LEVEL_0)) {
/* restore all FLASH pages as non-secure */
return ERROR_OK;
}
+ /* Workaround for STM32WL5x devices:
+ * DBGMCU_IDCODE cannot be read using CPU1 (Cortex-M0+) at AP1,
+ * to solve this read the UID64 (IEEE 64-bit unique device ID register) */
+
+ struct cortex_m_common *cortex_m = target_to_cm(bank->target);
+
+ if (cortex_m->core_info->partno == CORTEX_M0P_PARTNO && cortex_m->armv7m.debug_ap->ap_num == 1) {
+ uint32_t uid64_ids;
+
+ /* UID64 is contains
+ * - Bits 63:32 : DEVNUM (unique device number, different for each individual device)
+ * - Bits 31:08 : STID (company ID) = 0x0080E1
+ * - Bits 07:00 : DEVID (device ID) = 0x15
+ *
+ * read only the fixed values {STID,DEVID} from UID64_IDS to identify the device as STM32WLx
+ */
+ retval = target_read_u32(bank->target, UID64_IDS, &uid64_ids);
+ if (retval == ERROR_OK && uid64_ids == UID64_IDS_STM32WL) {
+ /* force the DEV_ID to 0x497 and the REV_ID to unknown */
+ *id = 0x00000497;
+ return ERROR_OK;
+ }
+ }
+
LOG_ERROR("can't get the device id");
return (retval == ERROR_OK) ? ERROR_FAIL : retval;
}
static int stm32l4_probe(struct flash_bank *bank)
{
struct target *target = bank->target;
+ struct armv7m_common *armv7m = target_to_armv7m(target);
struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
const struct stm32l4_part_info *part_info;
uint16_t flash_size_kb = 0xffff;
case 0x466: /* STM32G03/G04xx */
case 0x468: /* STM32G43/G44xx */
case 0x479: /* STM32G49/G4Axx */
- case 0x497: /* STM32WLEx */
/* single bank flash */
page_size_kb = 2;
num_pages = flash_size_kb / page_size_kb;
num_pages = flash_size_kb / page_size_kb;
stm32l4_info->bank1_sectors = num_pages;
break;
+ case 0x497: /* STM32WLEx/WL5x */
+ /* single bank flash */
+ page_size_kb = 2;
+ num_pages = flash_size_kb / page_size_kb;
+ stm32l4_info->bank1_sectors = num_pages;
+ if (armv7m->debug_ap->ap_num == 1)
+ stm32l4_info->flash_regs = stm32wl_cpu2_flash_regs;
+ break;
default:
LOG_ERROR("unsupported device");
return ERROR_FAIL;
retval = stm32l4_wait_status_busy(bank, FLASH_ERASE_TIMEOUT);
err_lock:
- retval2 = stm32l4_write_flash_reg_by_index(bank, STM32_FLASH_CR_INDEX, FLASH_LOCK);
+ retval2 = stm32l4_write_flash_reg_by_index(bank, stm32l4_get_flash_cr_with_lock_index(bank), FLASH_LOCK);
if (stm32l4_info->tzen && (stm32l4_info->rdp == RDP_LEVEL_0)) {
/* restore all FLASH pages as non-secure */
set _CHIPNAME stm32wlx
}
-set _ENDIAN little
+if { [info exists DUAL_CORE] } {
+ set $_CHIPNAME.DUAL_CORE $DUAL_CORE
+ unset DUAL_CORE
+} else {
+ set $_CHIPNAME.DUAL_CORE 0
+}
+
+if { [info exists WKUP_CM0P] } {
+ set $_CHIPNAME.WKUP_CM0P $WKUP_CM0P
+ unset WKUP_CM0P
+} else {
+ set $_CHIPNAME.WKUP_CM0P 0
+}
+
+# Issue a warning when hla is used, and fallback to single core configuration
+if { [set $_CHIPNAME.DUAL_CORE] && [using_hla] } {
+ echo "Warning : hla does not support multicore debugging"
+ set $_CHIPNAME.DUAL_CORE 0
+ set $_CHIPNAME.WKUP_CM0P 0
+}
+# setup the Work-area start address and size
# Work-area is a space in RAM used for flash programming
-# By default use 20kB
+
+# Memory map for known devices:
+# STM32WL x5JC x5JB x5J8
+# FLASH 256 128 64
+# SRAM1 32 16 0
+# SRAM2 32 32 20
+
+# By default use 8kB
if { [info exists WORKAREASIZE] } {
set _WORKAREASIZE $WORKAREASIZE
} else {
- set _WORKAREASIZE 0x5000
+ set _WORKAREASIZE 0x2000
}
+# Use SRAM2 as work area (some devices do not have SRAM1):
+set WORKAREASTART_CM4 0x20008000
+set WORKAREASTART_CM0P [expr {$WORKAREASTART_CM4 + $_WORKAREASIZE}]
+
#jtag scan chain
if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
jtag newtap $_CHIPNAME bs -irlen 5
}
-set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
-
-$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
-
-flash bank $_CHIPNAME.flash stm32l4x 0x08000000 0 0 0 $_TARGETNAME
-flash bank $_CHIPNAME.otp stm32l4x 0x1fff7000 0 0 0 $_TARGETNAME
-
-# Common knowledges tells JTAG speed should be <= F_CPU/6.
-# F_CPU after reset is MSI 4MHz, so use F_JTAG = 500 kHz to stay on
-# the safe side.
-#
-# Note that there is a pretty wide band where things are
-# more or less stable, see http://openocd.zylin.com/#/c/3366/
-adapter speed 500
+target create $_CHIPNAME.cpu0 cortex_m -endian little -dap $_CHIPNAME.dap
-adapter srst delay 100
-if {[using_jtag]} {
- jtag_ntrst_delay 100
-}
+$_CHIPNAME.cpu0 configure -work-area-phys $WORKAREASTART_CM4 -work-area-size $_WORKAREASIZE -work-area-backup 0
-reset_config srst_nogate
+flash bank $_CHIPNAME.flash.cpu0 stm32l4x 0x08000000 0 0 0 $_CHIPNAME.cpu0
+flash bank $_CHIPNAME.otp.cpu0 stm32l4x 0x1fff7000 0 0 0 $_CHIPNAME.cpu0
if {![using_hla]} {
# if srst is not fitted use SYSRESETREQ to
# perform a soft reset
- cortex_m reset_config sysresetreq
+ $_CHIPNAME.cpu0 cortex_m reset_config sysresetreq
}
-$_TARGETNAME configure -event reset-init {
+$_CHIPNAME.cpu0 configure -event reset-init {
# CPU comes out of reset with MSI_ON | MSI_RDY | MSI Range 4 MHz.
# Configure system to use MSI 24 MHz clock, compliant with VOS default Range1.
# 2 WS compliant with VOS=Range1 and 24 MHz.
adapter speed 4000
}
-$_TARGETNAME configure -event reset-start {
+$_CHIPNAME.cpu0 configure -event reset-start {
# Reset clock is MSI (4 MHz)
adapter speed 500
}
-$_TARGETNAME configure -event examine-end {
+$_CHIPNAME.cpu0 configure -event examine-end {
# Enable debug during low power modes (uses more power)
# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
mmw 0xE0042004 0x00000007 0
# Stop watchdog counters during halt
# DBGMCU_APB1_FZR1 |= DBG_IWDG_STOP | DBG_WWDG_STOP
mmw 0xE004203C 0x00001800 0
+
+ set _CHIPNAME [stm32wlx_get_chipname]
+ global $_CHIPNAME.WKUP_CM0P
+
+ if {[set $_CHIPNAME.WKUP_CM0P]} {
+ stm32wlx_wkup_cm0p
+ }
}
-$_TARGETNAME configure -event trace-config {
+$_CHIPNAME.cpu0 configure -event trace-config {
# nothing to do
}
+
+if {[set $_CHIPNAME.DUAL_CORE]} {
+ target create $_CHIPNAME.cpu1 cortex_m -endian little -dap $_CHIPNAME.dap -ap-num 1
+
+ $_CHIPNAME.cpu0 configure -work-area-phys $WORKAREASTART_CM0P -work-area-size $_WORKAREASIZE -work-area-backup 0
+
+ flash bank $_CHIPNAME.flash.cpu1 stm32l4x 0x08000000 0 0 0 $_CHIPNAME.cpu1
+ flash bank $_CHIPNAME.otp.cpu1 stm32l4x 0x1fff7000 0 0 0 $_CHIPNAME.cpu1
+
+ if {![using_hla]} {
+ # if srst is not fitted use SYSRESETREQ to
+ # perform a soft reset
+ $_CHIPNAME.cpu1 cortex_m reset_config sysresetreq
+ }
+
+ proc stm32wlx_wkup_cm0p {} {
+ set _CHIPNAME [stm32wlx_get_chipname]
+
+ # enable CPU2 boot after reset and after wakeup from Stop or Standby mode
+ # PWR_CR4 |= C2BOOT
+ stm32wlx_mmw $_CHIPNAME.cpu0 0x5800040C 0x00008000 0
+ }
+}
+
+# get _CHIPNAME from current target
+proc stm32wlx_get_chipname {} {
+ set t [target current]
+ set sep [string last "." $t]
+ if {$sep == -1} {
+ return $t
+ }
+ return [string range $t 0 [expr $sep - 1]]
+}
+
+# like mrw, but with target selection
+proc stm32wlx_mrw {used_target reg} {
+ set value ""
+ $used_target mem2array value 32 $reg 1
+ return $value(0)
+}
+
+# like mmw, but with target selection
+proc stm32wlx_mmw {used_target reg setbits clearbits} {
+ set old [stm32wlx_mrw $used_target $reg]
+ set new [expr {($old & ~$clearbits) | $setbits}]
+ $used_target mww $reg $new
+}
+
+# Make sure that cpu0 is selected
+targets $_CHIPNAME.cpu0
+
+# Common knowledges tells JTAG speed should be <= F_CPU/6.
+# F_CPU after reset is MSI 4MHz, so use F_JTAG = 500 kHz to stay on
+# the safe side.
+#
+# Note that there is a pretty wide band where things are
+# more or less stable, see http://openocd.zylin.com/#/c/3366/
+adapter speed 500
+
+adapter srst delay 100
+if {[using_jtag]} {
+ jtag_ntrst_delay 100
+}
+
+reset_config srst_nogate
Code Review / openocd.git / commitdiff